Abstract:In this paper, a high-resistivity silicon (HR-Si) interposer integrated with through-silicon via (TSV) electrically grounded coplanar waveguide (CPW) line is presented for 2.5-D/3-D heterogeneous integration of radio frequency (RF) microelectronics devices. In addition, design of TSV interconnection composed of two coaxial ladder-hollow-annular Cu (copper) TSVs of different diameters is utilized to maintain a sufficient freedom for strict standard cleaning to avoid Si resistivity degradation. The formation of the coaxial ladder TSV structure is more beneficial to the subsequent plating process because it reduces the aspect ratio of TSV vias. Hollow-annular Cu TSV is manufactured in order to reduce the problem of mismatch in coefficient of thermal expansion among TSV's constituent materials. A layer of Au (aurum) film is utilized to passivate the exposed Cu surface of Si interposer. Au is widely used in III-V groups' devices because of the good compatibility with photonic integrated circuits, conductivity, and corrosion resistance. HR-Si interposer with TSV grounded CPW line and test structure is fabricated and characterized. With the monitoring test results, it can be found that it changes little in the resistivity of Si substrate, though the whole process, which is a basic requirement for RF performance. RF property test results show that the insertion loss is about -0.20 dB/mm at 10 GHz for the presented TSV grounded CPW line and -0.02 dB per TSV. These test results are better than the traditional design. To verify its applicability to 2.5-D/3-D heterogeneous integration, RF microelectronics die is assembled on TSV interposer and tested, and the test results prove that it works properly.

Process Development of Thick Si Interposer for 2.5d Integration of Rf Mems Devices

Process Development of A New Tgv Interposer for Wafer Level Package of Inertial Mems Device

Fabrication and RF Property Evaluation of High-Resistivity Si Interposer for 2.5-D/3-D Heterogeneous Integration of RF Devices

A 2.5D Integrated L Band Receiver Based on High Resistivity Si Interposer

3D Heterogenous Integrated Wideband Switchable Bandpass Filter Bank for Millimeter Wave Applications

A Compact 2-18Ghz Ultra-Wideband Frequency-conversion T/R Module Based on a 3D Heterogeneous Integrated Process

A RF Redundant TSV Interconnection for High Resistance Si Interposer

Thermal and Electrical Characterization of TSV Interposer Embedded with Microchannel for 2.5D Integration of GaN RF Devices

Design, Fabrication and Characterization of a Novel TSV Interposer Integrated Inductor for RF Applications

Double-Shielded Interposer with Highly Doped Layers for High-Speed Signal Propagation

Design, process, and electrical verification of HR-Si interposer for 3D heterogeneous RF integration

Fabrication Process of A Tsv Interposer for Radio Frequency Chip with Integrated Passive Devices

Fabrication of Microchannel Embedded Tsv Interposer and Its Influence on Tsv'S Electrical Parameters

Development of Through-Substrate Via Process for Silicon-Based Monolithic Microwave Integrated Circuits SIS Mixer

Design, Fabrication, and Radio Frequency Property Evaluation of a Through-Glass-via Interposer for 2.5D Radio Frequency Integration

Process Development and Characterization for Integrating Microchannel into Tsv Interposer

Fabrication and Characterization of Annular Copper Through-Silicon Via for Passive Interposer Applications

Fabrication and Characterization of a Low Parasitic Capacitance and Low-Stress Si Interposer for 2.5-D Integration

Interposer Fabrication with Annular Copper Tsv and Multi-Layered Redistribution Layer

Fabrication, Characterization, and Simulation of a Low-Cost TSV Integration Without Front-Side CMP Process

Process Development of Through-Glass-Via (tgv) Interposer for Radio Frequency (rf) Applications