Abstract:This article focuses on realizing wideband compartment shielding in the shielding can packages of miniaturized high-speed chip modules and circuits. Because the conventional diaphragms with a low profile are difficult to cope with the high-order mode interference and evanescent wave interference, a new “meta-diaphragm,” which is based on the single-negative (SNG) metamaterial, is proposed to address these inherent problems. It is demonstrated that benefitting from the large propagation attenuation introduced by the proposed meta-diaphragm, a good shielding performance can be achieved at the first higher order resonance mode. Moreover, by elaborately embedding resistors in the meta-diaphragm, the additional interferences at other resonance frequencies can be significantly suppressed. Furthermore, the structure of the meta-diaphragm is optimized with two approaches: evolving from the single-band SNG structure to the double-band one and integrating with the parasitic patches. The two approaches enable its independent controlling ability at different frequency ranges and enhancement of low-frequency shielding performance. Based on the proposed technique, an experiment is implemented to suppress the resonance-dominated interference between the passive traces in a shielding can. The result agrees well with those from theoretical prediction. The final experimental shielding can’s profile and width are 5 and 20 mm, respectively; the meta-diaphragm’s profile is only 1.5 mm, i.e., < 1/3 of shielding can’s profile, and its electrically length is only 3 mm, i.e., $0.1\lambda _{0}$ at 10 GHz, and the measured (simulated) meta-diaphragm can significantly suppress radio frequency interference (RFI) within 10.2–17 GHz (10–16.9 GHz) and realize $< -33.5$ dB ( $< -40$ dB) coupling within 100 kHz–18 GHz (dc-to-20 GHz). The miniaturized dimension and wideband results indicate that our proposed technique could meet the compartment shielding requirement of a series of miniaturized packages in the practical radio frequency (RF) chip modules and circuits.

Double-Shielded Interposer with Highly Doped Layers for High-Speed Signal Propagation

A Shielding Structure for Crosstalk Reduction in Silicon Interposer

Modeling and Measurement of A Novel Shielding Design in Silicon Interposer

A Wideband Model for On-Chip Interconnects with Different Shielding Structures

A Novel Dieletric Slot Stripline Structure for Millimeter Wave Flexible Printed Circuit

Methods and designs for improving the signal integrity for 3D electrical interconnects in high performance IC packaging

On the Efficacy of Through-Silicon-Via Inductors

PDN Impedance Modeling for Multiple Through Vias Array in Doped Silicon

A Rigorous Model for Through-Silicon Vias with Ohmic Contact in Silicon Interposer

Crosstalk Reduction in TSV Arrays with Direct Ohmic Contact Between Metal and Silicon-Substrate

A RF Redundant TSV Interconnection for High Resistance Si Interposer

Electrical Characterization of Shielded TSVs With Airgap Isolation for RF/mmWave Applications

Different designs of TSVs for 3D IC: Signal integrity analysis with cascaded scattering matrix

Fabrication and RF Property Evaluation of High-Resistivity Si Interposer for 2.5-D/3-D Heterogeneous Integration of RF Devices

Modeling of the RF Coaxial TSV Configuration Inside the Silicon Interposer with Embedded Cooling Cavity

Wideband Compartment Shielding Technique for Miniaturized Packages Based on Electrically Small Single-Negative Meta-Diaphragm

Design, Fabrication, and Radio Frequency Property Evaluation of a Through-Glass-via Interposer for 2.5D Radio Frequency Integration

A 2.5D Integrated L Band Receiver Based on High Resistivity Si Interposer

A Novel Interposer Channel Structure with Vertical Tabbed Vias to Reduce Far-End Crosstalk for Next-Generation High-Bandwidth Memory

An ultra-deep TSV technique enabled by the dual catalysis-based electroless plating of combined barrier and seed layers

Process Development of Thick Si Interposer for 2.5d Integration of Rf Mems Devices