Abstract:Rare-earth-doped SiAlON and Si3N4 materials from aluminosilicate starting materials have been reported to show superior photoluminescence (PL) properties. Three different starting materials, including pulverized coal furnace fly ash, diatomite and raw illite, were used for synthesis of nitride materials. The phase and morphology evolution of these products were carefully monitored at the low temperature range of 1350 °C to 1450 °C by X-ray diffraction (XRD), scanning electronic microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR). The PL properties of Eu-doped nitride products were also comparatively characterized. The results show that the type of starting material affects the phase composition and the photoluminescence properties of products. The existence of aluminum and alkali metals could effectively promote nitridation reactions. Aluminum in the starting materials led to the formation of different aluminum-rich nitride phases. Thus, β-SiAlON could be achieved at a much lower temperature (1350 °C) using raw illite or fly ash containing the proper amount of aluminum. Additionally, excess aluminum led to the formation of corundum and 15R-SiAlON. The products from pulverized coal furnace fly ash had more prismatic particles, and the products from diatomite had more fibrous particles. With the progress of the nitridation process, the fibers were increased, becoming longer and straighter, and the prismatic particles were more obvious. The presence of aluminum in the starting materials led to a blue shift in the photoluminescence spectrum.

Phase Behavior Analysis of Low-Grade Bauxite and Rutile by Carbothermal Reduction-Nitridation

Synthesis of Β-Sialon/ti(c,n) Composites Using Low and Middle Grade Bauxite and Ilmenite by Carbothermal Reduction-Nitridation

Study on Synthesizing Diphase Sialon from Lower Al2O3 Bauxite by Carbothermal Reduction-Nitridation

Influence of Sintering Temperature on Phase Behavior of Products from Rutile and Quartz by Aluminothermic Reduction Nitridation

Synthesis of TiN-Si3N4 Composites from Rutile and Quartz by Carbothermal Reduction Nitridation

Effect of Reaction Temperature on the Synthesis of Β-Sialon/ti(c, N) Composites from Low Grade Bauxite and Ilmenite

Phase Analysis of Forsterite in Carbothermal Reduction Processing

Phase transformation of high aluminium fly ash in carbothermal reduction–nitridation at high temperatures

Phase behaviors of talc minerals in carbothermal reduction process

Phase Behavior of Silica Brick Used in Carbothermal Reduction

Carbothermal Reduction Nitridation of Fly Ash, Diatomite and Raw Illite: Formation of Nitride Powders with Different Morphology and Photoluminescence Properties

Effect of Temperature on the Phase Behaviors of Zircon by Carbothermal Reduction-Nitridation

Synthesis of β-Si3N4 powder from quartz via carbothermal reduction nitridation

Influence of Temperature on Phase Composition of Nitridation Products from Rutile and Fly Ash

Phases transformation of high-alumina fly ash under carbothermal reduction and nitridation

Synthesis of Β-Sialon/ti(c, N) Powders from Mineral Waste Residue Via Carbothermal Reduction Nitridation

Carbothermal/aluminothermic Reduction Nitridation Synthesis of ZrN–SiAlON Refractory Composites from Zircon and Bauxite: a Comparative Study of the Reduction Effect of Reducers

Synthesis of Ti(C,N) Powder Via CRN Method from Rutile/Carbon Mixtures

Phases Transformation of Boron Mud During Carbothermal Reduction Process

Phase composition analysis of TiN-Al_2O_3 synthesized from aluminum-containing and rutile by aluminothermic reduction-nitridation method

Preparation Of Al2o3-Sic Composite Powder From Kyanite Tailings Via Carbothermal Reduction Process