Abstract:Rare-earth-doped SiAlON and Si3N4 materials from aluminosilicate starting materials have been reported to show superior photoluminescence (PL) properties. Three different starting materials, including pulverized coal furnace fly ash, diatomite and raw illite, were used for synthesis of nitride materials. The phase and morphology evolution of these products were carefully monitored at the low temperature range of 1350 °C to 1450 °C by X-ray diffraction (XRD), scanning electronic microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR). The PL properties of Eu-doped nitride products were also comparatively characterized. The results show that the type of starting material affects the phase composition and the photoluminescence properties of products. The existence of aluminum and alkali metals could effectively promote nitridation reactions. Aluminum in the starting materials led to the formation of different aluminum-rich nitride phases. Thus, β-SiAlON could be achieved at a much lower temperature (1350 °C) using raw illite or fly ash containing the proper amount of aluminum. Additionally, excess aluminum led to the formation of corundum and 15R-SiAlON. The products from pulverized coal furnace fly ash had more prismatic particles, and the products from diatomite had more fibrous particles. With the progress of the nitridation process, the fibers were increased, becoming longer and straighter, and the prismatic particles were more obvious. The presence of aluminum in the starting materials led to a blue shift in the photoluminescence spectrum.

Phase transformation of high aluminium fly ash in carbothermal reduction–nitridation at high temperatures

Phases transformation of high-alumina fly ash under carbothermal reduction and nitridation

Carbothermal Reduction Nitridation of Fly Ash, Diatomite and Raw Illite: Formation of Nitride Powders with Different Morphology and Photoluminescence Properties

Dilithium Dialuminium Trisilicate Crystalline Phase Prepared from Coal Fly Ash

Phase transformation of MgAl2O4 -SiAlON composites synthesized by carbonthermal reduction and nitridation method from magnesite and bauxite

Synthesis of Sialon Powders from Aluminium Dross and Fly Ashes

Synthesis of Sialon-Mullite Composites Using Fly Ash by Carbon-Thermal Reduction Nitridation

Preparation of Β-Sialon from Fly Ash by Carbothermal Reduction-Nitridation Reaction

Synthesis of Rod-Like Α-Sialon by Carbothermal Reduction-Nitridation

Influence of Temperature on Phase Composition of Nitridation Products from Rutile and Fly Ash

Influence of Sintering Temperature on Phase Behavior of Products from Rutile and Quartz by Aluminothermic Reduction Nitridation

Preparation and Characterization of Β-Sialon Ceramics from High Aluminium Fly Ash Via Carbothermal Reduction-Nitridation

Phase Transformation of High Alkaline Ash Residue on the Process of Sintering and Fusion

Synthesis of Si 3 N 4 powder with tunable α/β-Si 3 N 4 content from waste silica fume using carbothermal reduction nitridation

Phase Behavior Analysis of Low-Grade Bauxite and Rutile by Carbothermal Reduction-Nitridation

Synthesis of Fe-Sialon Composites Using High Alumina Coal Gangue by Carbothermal Nitridation

Synthesis of Β-Sialon/ti(c,n) Composites Using Low and Middle Grade Bauxite and Ilmenite by Carbothermal Reduction-Nitridation

Effects of Sodium Carbonate and Sodium Chloride Additives on Alkaline Fusion of Coal Fly Ash

The Carbon Environment Effects on Phase Composition and Photoluminescence Properties of Β-Sialon Multiphase Materials Prepared from Fly Ash Acid Slag

Phase transformation of coal gangue by aluminothermic reduction nitridation: Influence of sintering temperature and aluminum content

Synthesis of Sialon-SiC Composites from Kyanite Tailings by Carbothermal Reduction Nitridation