Abstract:Monotonic tensile behavior of plain-woven SiCf/SiC ceramic matrix composites is investigated at 1200 °C and 1350 °C in water–oxygen environments. In addition, tensile–tensile fatigue behavior at 1200 °C in water–oxygen environments is discussed. Specimens are prepared using chemical vapor infiltration (CVI) process. To enhance their resistance to oxidation in high-temperature water–oxygen environments, environmental barrier coatings (EBCs) are deposited on their surface. Two rows of film cooling holes (FCHs) with 0.5 mm diameter, each row consisting of five FCHs, are designed to compare the effects of two different hole spacings on specimen fatigue and tensile performance. The evolution of strain and normalized modulus during fatigue cycling is investigated in detail. Microstructures of specimens that failed under tensile and fatigue conditions are observed using scanning electron microscopy (SEM), and elemental analyses of specimens after fatigue test failure are performed using energy-dispersive spectroscopy (EDS). The results reveal that tensile strength of specimens with large FCH spacing is greater than that of specimens with small FCH spacing. However, fatigue performance of specimens with small FCH spacing was better than that of specimens with large FCH spacing. This phenomenon is caused by a reduction in strength due to stress concentration effect near holes with small FCH spacing. Holes with large FCH spacing are closer to the specimen edge during fatigue test, leading to high failure rate. The oxidation and embrittlement that surround holes caused by FCHs compromised structural integrity of the specimen and allowed water–oxygen environment to penetrate the specimen interior. This has significant impact on mechanical performance of the material.

Microstructure, Tensile Strength and Thermostability of W-core SiC Fibers with or Without Carbon Coating

MICROSTRUCTURES AND PROPERTIES OF HOT-EXTRUDED SiCW/6061Al COMPOSITES

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

The fiber structure evolution and performance changes of SiC–ZrC fibers after 1600 °C heat treatment

Effect of long-time annealing at high temperature on the microstructure and mechanical properties of different types of SiC fibers

Structural evolution and mechanical properties of Cansas-III SiC fibers after thermal treatment up to 1700 °C

Mechanical properties and microstructural evolution of Cansas-III SiC fibers after thermal exposure in different atmospheres

Mechanical properties and microstructure evolution of KD‐SA SiCf/BN/SiC CMCs oxidized at different temperatures

High-temperature tensile behavior of 3D SiC/SiC composites

Preparation and high-temperature properties of skin–core structure SiC ceramic fibers

Thermal stability of CVI and RMI SiC/SiC composites adopting Cansas 3303 SiC fibers

Study of SiC fiber axial compressive behavior using tensile recoil measurement

Microstructure and corrosion behavior of in-situ grown Y3Si2C2 coated SiC fibers exposed to air and wet-oxygen at 1400 °C

Tensile-tensile fatigue behavior of plain-woven SiCf/SiC ceramic matrix composites with differently spaced film cooling holes and environmental barrier coatings in high-temperature water-oxygen environments

Tensile Mechanical Behavior and Failure Mechanism of a Plain-Woven SiCf/SiC Composites at Room and Elevated Temperatures

Microstructure and mechanical properties of SiC fiber/Si-CoSi2 matrix composites fabricated by carbon chemical vapor infiltration and Si alloy melt infiltration process

Study on the Mechanical Property of High‐Performance Silicon Carbide Fiber

Structure and properties of fine diameter continuous SiC ceramic fiber reinforced Al matrix composites

Interfacial Reactions and Mechanical Properties Studies of C-Coated and C/B4C Duplex-Coated SiC Fiber-Reinforced Ti2AlNb Composites

Effect of CVI SiC interphase on tensile properties of SiC fibers with different surfaces

Tensile behavior of the designed SiCf/Ti2AlNb/Ti17 composites