Abstract:High-textured pyrolytic carbon (PyC) is the ideal interface for SiC fiber-reinforced SiC matrix (SiCf/SiC) composites. To prepare high-textured PyC coatings on SiC fibers efficiently, chemical vapor deposition (CVD) technique was applied with the single precursor ethanol. The effects of CVD parameters on the morphology and textures of PyC were investigated in detail. Rough laminar (RL), smooth laminar (SL) and regenerative laminar (ReL) PyC could be obtained by controlling the CVD parameters. High-textured RL PyC could be stably synthesized in a large distance range in the horizontal tube furnace at 1150 °C and 10–20 kPa (total pressure), which inferred that low temperature and negative pressure were beneficial to the formation of RL PyC. Conversely, when the temperature was up to 1350 °C, the textures of PyC at different deposition positions varied considerably. In the vicinity of isothermal zone, the texture evolution of PyC with deposition positions followed the pattern of SL→RL→SL, which could be ascribed to the ratio change of the small linear hydrocarbons (fillers) and the aromatic hydrocarbons (particles) in the gas phase. The texture evolution followed the Particle-Filler model. In addition to PyC textures, the PyC coating thickness played a critical role in regulating the mechanical properties of SiC fibers and SiCf/SiC composites. In the present work, the effects of thickness of RL PyC coatings on the tensile properties of SiC fibers were investigated. The SiC fibers with 0.3 μm RL PyC coating showed the highest average tensile strength (2735 MPa) and Weilbull modulus (10.34), which might be ascribed to the repair of fiber surface defects and the appropriate stress state between fibers and coatings. The results could provide essential data for the interface design and optimization of SiCf/SiC composites.

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Mechanical Properties of 3D KD-I SiCf/SiC Composites with Engineered Fibre–matrix Interfaces

Effect of SiC coating and heat treatment on damping behavior of C/SiC composites

Effect of SiC content on the mechanical behaviour of a three-dimensional needled C/SiC composite

Texture control of pyrolytic carbon coatings and effects of coating thickness on the tensile properties of SiC fibers

Interfacial Reactions and Mechanical Properties Studies of C-Coated and C/B4C Duplex-Coated SiC Fiber-Reinforced Ti2AlNb Composites

Effects of the fiber surface characteristics on the interfacial microstructure and mechanical properties of the KD SiC fiber reinforced SiC matrix composites

Effect of the Incorporation of SiC Nanowire with Double Protective Layers on SiC Coating for C/C Composites

Investigation of Impact of C/Si Ratio on the Friction and Wear Behavior of Si/SiC Coatings Prepared on C/C-SiC Composites by Slurry Reaction Sintering and Chemical Vapor Infiltration

The Effect of PyC/SiC Compound Interphase on the Properties of PIP SiC/SiC Composite

Microstructure and mechanical properties of SiC fiber/Si-CoSi2 matrix composites fabricated by carbon chemical vapor infiltration and Si alloy melt infiltration process

Synthesis of coatings on SiC fibers and their effects on microstructure and mechanical properties of SiC f /SiBCN composites

Effects of Interphase Thickness on Damping Behavior of 2D C/SiC Composites

Mechanical and thermal shock properties of C f /SiBCN composite: Effect of sintering densification and fiber coating

Influence of thickness of pyrolytic carbon interphase on the mechanical behavior of SiC/(BN/PyC)/SiC composites

Improved antioxidative and mechanical properties of SiC coated C/C composites via a SiO2-SiC reticulated layer

Thickness effect of an alumina–zirconia–mullite composite coating on the properties of zirconia

Preparation and tensile behavior of SiCf/SiC mini composites containing different types and thicknesses of interphase

Experimental and Numerical Investigation on SiC Coating Delamination from C/SiC Composites

Effect of CVI SiC interphase on tensile properties of SiC fibers with different surfaces