Abstract:Precursor infiltration and pyrolysis (PIP) and chemical vapor infiltration (CVI) were used to fabricate SiC/SiC composites on a four-step 3D SiC fibre preform deposited with a pyrolytic carbon interface. The effects of fabrication processes on the microstructure and mechanical properties of the SiC/SiC composites were studied. Results showed the presence of irregular cracks in the matrix of the SiC/SiC composites prepared through PIP, and the crystal structure was amorphous. The room temperature flexural strength and modulus were 873.62 MPa and 98.16 GPa, respectively. The matrix of the SiC/SiC composites prepared through CVI was tightly bonded without cracks, the crystal structure had high crystallinity, and the room temperature bending strength and modulus were 790.79 MPa and 150.32 GPa, respectively. After heat treatment at 1300 degrees C for 50 h, the flexural strength and modulus retention rate of the SiC/SiC composites prepared through PIP were 50.01% and 61.87%, and those of the composites prepared through CVI were 99.24% and 96.18%, respectively. The mechanism of the evolution of the mechanical properties after heat treatment was examined, and the analysis revealed that it was caused by the different fabrication processes of the SiC matrix. After heat treatment, the SiC crystallites prepared through PIP greatly increased, and the SiOxCy in the matrix decomposed to produce volatile gases SiO and/or CO, ultimately leading to an increase in the number of cracks and porosity in the material and a decrease in the material load-bearing capacity. However, the size of the SiC crystallites prepared through CVI hardly changed, the SiC matrix was tightly bonded without cracks, and the load-bearing capacity only slightly changed.

The Effect of PyC/SiC Compound Interphase on the Properties of PIP SiC/SiC Composite

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Mechanical Properties of 3D KD-I SiCf/SiC Composites with Engineered Fibre–matrix Interfaces

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

Effects of the Single Layer Cvd Sic Interphases on the Mechanical Properties of the Sicf/Sic Composites Fabricated by Pip Process

Mechanical properties and oxidation resistance of SiC f/CVI-SiC composites with PIP-SiC interphase

Effects of SiC Interphase on the Mechanical and Ablation Properties of C/C-ZrC-ZrB 2 -Sic Composites Prepared by Precursor Infiltration and Pyrolysis

Effects of CVI SiC amount and deposition rates on properties of SiCf/SiC composites fabricated by hybrid chemical vapor infiltration (CVI) and precursor infiltration and pyrolysis (PIP) routes

Effect of PyC/BN interfacial phases on mechanical behavior of SiC/SiC composites

Effect of Pyc Interphase Thickness on Mechanical Behaviors of Sibc Matrix Modified C/Sic Composites Fabricated by Reactive Melt Infiltration

The Effect of the Pyc Interphase Coating on the Microwave Heating Sintered Sic/Sic Composites

Effects of interphases on thermal expansion of 3D-C/SIC composites

Influence of polycarbosilane composition on the properties of SiC/SiC composite fabricated by precursor infiltration and pyrolysis process

Effect of PIP Process on Microstructure and Mechanical Properties of 2D C/SiC-ZrB_2 Composites

Mechanical Properties and Failure Behavior of 3D-SiCf/SiC Composites with Different Interphases

Influence of thickness of pyrolytic carbon interphase on the mechanical behavior of SiC/(BN/PyC)/SiC composites

Microstructure, Interfacial and Mechanical Properties of SiC Interphase Modified C/C-SiC Composites Prepared by Reactive Melt Infiltration

Effects of fabrication processes on the properties of SiC/SiC composites

Processing and Properties of 2D SiC/SiC Composites by Precursor Infiltration and Pyrolysis

Effect of polymer infiltration and pyrolysis (PIP) on microstructure and properties of high volume fraction SiC/Al composites prepared by a novel hybrid additive manufacturing

Effect of chemical vapor infiltration on the flexural properties of C/C-SiC composites prepared by the precursor infiltration pyrolysis method