Abstract:The solid-state processing and utilization of light-metal-based composites align with green policies by reducing the weight of components and employing lower processing temperatures compared to traditional metallurgical methods. This study explores the incorporation of SiC particles at concentrations of 5 and 10 wt.% into an Al4Cu matrix through powder mixing, compaction at 235 MPa, hot extrusion, and sintering at 600 °C in a nitrogen atmosphere. The resulting microstructure, hardness, compressive strength, and flexural strength of the composites were evaluated. During extrusion, the composite underwent plastic deformation, leading to cracking and fragmentation of the SiC particles within the matrix. Therefore, evenly distributed reinforcing particles with a diameter much smaller than the originally introduced ceramic particles were observed. Recrystallization also occurred, with Al 2 Cu precipitates forming on grain boundaries and nanosized Al 2 O 3 oxides observed in porous areas and at matrix-reinforcement interphase boundaries. The composite containing 5 wt.% SiC exhibited the highest compressive strength of 305 MPa, while the composite with 10 wt.% SiC achieved the highest flexural strength of 889 MPa. However, non-deformable SiC particles crack before reaching maximum strength due to stress concentration at their sharp edges, initiating microcracks in the matrix. Microstructural analysis further revealed that SiC particles tend to crack during hot extrusion, reducing their effectiveness in stress transfer. The hardness remained constant at 78 HV1, irrespective of SiC content. These findings demonstrate that the addition of SiC particles significantly enhances the mechanical properties of Al4Cu composites, making them promising materials for lightweight and high-strength applications.

MICROSTRUCTURES AND PROPERTIES OF HOT-EXTRUDED SiCW/6061Al COMPOSITES

Forming process of hot-extruded SiCw/6061AI composites(I)

Effect of hot extrusion on the microstructure and mechanical properties of SiCNWs/Mg-2Zn-0.1Y composite

Hot extrusion of SiCp/Al-Cu composites: optimizing mechanical properties through microstructural control

Analysis of processing map and parameters optimization during hot extrusion of 17 vol.% SiCp/2009Al composite

Microstructure and mechanical properties of Al−Mg−Si alloy U-shaped profile

Microstructure evolution of SiC whisker-reinforced Ti6Al4V matrix composites manufactured by selective laser melting during heat treatment

Structure–property relationships of SiC reinforced advanced Al–Zn–Mg–Cu alloy

Strengthening mechanism and anisotropy of mechanical properties of Si3N4p/Al-Mg-Si composites fabricated by sintering and extrusion

Hot Deformation Behavior and Mechanisms of SiC Particle Reinforced Al-Zn-Mg-Cu Alloy Matrix Composites

Effect of microstructures on mechanical properties of Ti‐6.5Al‐2Sn‐4Zr‐4Mo‐1W‐0.2Si alloy

Investigation of Microstructures and Mechanical Properties of SiC/AA2024 Nanocomposites Processed by Powder Metallurgy and T6 Heat Treatment

Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites

Effect of heat treatment on the microstructure, mechanical properties and fracture behaviors of ultra-high-strength SiC/Al–Zn–Mg–Cu composites

Two Directional Microstructure and Effects of Nanoscale Dispersed Si Particles on Microhardness and Tensile Properties of AlSi7Mg Melt-Spun Alloy

Microstructures and Tensile Properties of an A1-12 Wt Pct Si Alloy Produced by Reciprocating Extrusion

Hot Workability of the Multi-Size SiC Particle-Reinforced 6013 Aluminum Matrix Composites

Structure and properties of fine diameter continuous SiC ceramic fiber reinforced Al matrix composites

Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy

Numerical Simulation of the Mechanical Properties and Fracture of SiCp/6061Al Composite Materials Based on Microstructure