Abstract:This study shows that a eutectic Al–12Si alloy with controllable ultrafine microstructure and excellent mechanical properties can be achieved by using selective laser melting and subsequent solution heat treatment. This provides a novel and promising approach to the refinement of eutectic Al–Si alloys. Unlike Al–12Si alloys fabricated and refined by traditional methods, the as-fabricated Al–12Si in this study contains nano-sized spherical Si particles surrounding a supersaturated Al matrix. During solution heat treatment, precipitation and coalescence of the Si particles occur, which decreases the Si concentration in the matrix and sub-micron to micron-sized spherical particles embedded in an Al matrix form. The as-fabricated Al–12Si exhibits significantly better tensile properties than the traditionally produced counterparts; while the solution treated Al–12Si has an extremely high ductility of approximately 25%. Importantly, the mechanical properties of the Al–12Si can be tailored through controlling the precipitation and coalescence of the Si particles by varying the solution heat treatment time. A detailed transmission electron microscopy study was conducted to investigate this Al–12Si alloy with ultrafine eutectic microstructure. The excellent tensile properties have been attributed to the refined eutectic microstructure containing spherical Si particles. The formation of this unique microstructure is due to the super heating and an extremely high cooling rate during selective laser melting and the subsequent solution heat treatment, which enables Si to grow along its most stable plane {111}Si.

Microstructures and Tensile Properties of an A1-12 Wt Pct Si Alloy Produced by Reciprocating Extrusion

The microstructures and properties of an al- 12 wt pct

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

MICROSTRUCTURES AND PROPERTIES OF HOT-EXTRUDED SiCW/6061Al COMPOSITES

Microstructural evolution and superplasticity of Al-5.8Mg-0.23Mn alloys processed by reciprocating extrusion

Microstructure and Mechanical Properties of Al-Si Alloys Produced by Rapid Solidification and Hot Extrusion

Synthesis of Fine Pb–50 Vol.-%Sn Alloys by a New Process of Reciprocating Extrusion

A Selective Laser Melting and Solution Heat Treatment Refined Al–12Si Alloy with a Controllable Ultrafine Eutectic Microstructure and 25% Tensile Ductility

Microstructure and mechanical properties of Al-Mg-Si alloy fabricated by a short process based on sub-rapid solidification

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

Microstructure and mechanical properties of Al−Mg−Si alloy U-shaped profile

Strengthening mechanism and anisotropy of mechanical properties of Si3N4p/Al-Mg-Si composites fabricated by sintering and extrusion

Microstructure and Mechanical Properties of a Bulk Ultrafine Grained Al–7Si–0.3Mg Alloy Produced by Thermomechanical Consolidation of a Nanocrystalline Powder

Fabrication of hypereutectic Al Si alloy with improved mechanical and thermal properties by hot extrusion

Microstructural Evolution and Mechanical Properties of a Continuously Cast Al–Mg–Si–Cu Alloy Processed by Repetitive Continuous Extrusion Forming

Effects of Fe-6.5wt.%Si alloys prepared by different cooling methods on ordered structure and mechanical properties

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Effect of extrusion temperatures on the microstructures, mechanical properties and thermal properties of PM Al-20Si alloy

A Novel Method for Improving the Microstructure and Properties of Al-Si-Cu Alloys Based on Rapid Solidification/Powder Metallurgy

Microstructure and Mechanical Properties of a Hot-Hydrostatically Extruded 93w–4.9ni–2.1fe Alloy

Effect of Al3(Sc, Zr) and Mg2Si Precipitates on Microstructure and Tensile Properties of Selective Laser Melted Al-14.1Mg-0.47Si-0.31Sc-0.17Zr Alloy