Abstract:Selective laser sintering (SLS) combined with reaction melt infiltration was used to fabricate Si–SiC ceramic matrix composites, and the effects of different concentrations of phenolic resin (PF) on the properties of the SLS green body and carbonized and final Si–SiC samples were investigated. The results showed that the impregnation with PF can increase the bulk density, reduce the porosity of the samples at all stages, and improve the mechanical properties of the reactive bonded samples. The degree of densification and mechanical properties of the sample gradually enhanced with an increase in PF concentration. The main phases of the Si–SiC composites were free Si, α-SiC, β-SiC, plus an extremely small amount of Al–Si alloy, and the SiC and the Si phase contents increased and decreased, respectively, as the concentration of PF increased when measured using Rietveld refinement and image analysis software. The macroscopic properties of the samples improved greatly after precursor infiltration pyrolysis (PIP) treatment with 66.7%vol PF-ethanol solution twice. According to the crystal nucleation-growth theory, it was inferred that the infiltrated PF could provide a certain amount of pyrolytic carbon in the carbonized specimen. During the reaction bonded process, the carbon formed by carbonization pyrolysis first dissolves into the molten Si and reaches saturation. With the further dissolution of carbon, [C] and [Si] in the liquid phase contact each other to form β-SiC nuclei, the nuclei that precipitate at the pore wall position and gradually form a continuous interfacial layer of β-SiC. The β-SiC layer prevents the liquid Si from direct contact with C inside the prefabricated body, therefore, further reactants diffuse through the layer. Finally, the fine crystalline β-SiC grains were fabricated inside the specimen.

Preparation of Complex-Shape SiC Ceramic Composites Parts Derived from Phenolic Resin Template

Effect of impregnated phenolic resin on the properties of Si–SiC ceramic matrix composites fabricated by SLS-RMI

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Properties regulation of SiC ceramics prepared via stereolithography combined with reactive melt infiltration techniques

Preparation of low residual silicon content Si-SiC ceramics by binder jetting additive manufacturing and liquid silicon infiltration

Preparation of Interconnected Porous Carbon Monoliths by Reaction-Induced Phase Separation and Pyrolysis

Three-dimensional printing of SiCN ceramic matrix composites from preceramic polysilazane by digital light processing

Microstructure Evolution Process of Porous Silicon Carbide Ceramics Prepared Through Coat-Mix Method

Preparation of Silicon Carbide/Graphite Composite Ceramic Sealing Material by Liquid Silicon Inifltration Processing

High‐strength Si–SiC lattices prepared by powder bed fusion, infiltration‐pyrolysis, and reactive silicon infiltration

Preparation of SiC ceramic fiber from a photosensitive polycarbosilane

Preparation and Pore Structure Characteristics of SiC Honeycomb Ceramics with Macroporous Walls

Formation Mechanism of Porous Silicon Carbide Ceramic Synthesized by Coat-Mix Process

Preparation of biomorphic porous SiC and SiO2 ceramics by sol infiltration into biotemplate followed by controlled sintering

Digital light processing of SiC ceramic from allylhydridopolycarbosilane with limited acrylate monomers

Preparation and Mechanism of Interconnected Mesoporous Carbon Monoliths from Phenolic Resin/Ethylene Glycol Mixtures

Preparation of Porous SiC Ceramic Using Bamboo Charcoal and Silica Sol As Pore-Forming Agents

Preparation and Properties of Porous Silicon Carbide Ceramics Through Coat-Mix and Composite Additives Process

Stereolithography-based additive manufacturing of lightweight and high-strength Cf/SiC ceramics

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Synthesis and characterization of submicron silicon carbide powders with silicon and phenolic resin