Abstract:Selective laser sintering (SLS) combined with reaction melt infiltration was used to fabricate Si–SiC ceramic matrix composites, and the effects of different concentrations of phenolic resin (PF) on the properties of the SLS green body and carbonized and final Si–SiC samples were investigated. The results showed that the impregnation with PF can increase the bulk density, reduce the porosity of the samples at all stages, and improve the mechanical properties of the reactive bonded samples. The degree of densification and mechanical properties of the sample gradually enhanced with an increase in PF concentration. The main phases of the Si–SiC composites were free Si, α-SiC, β-SiC, plus an extremely small amount of Al–Si alloy, and the SiC and the Si phase contents increased and decreased, respectively, as the concentration of PF increased when measured using Rietveld refinement and image analysis software. The macroscopic properties of the samples improved greatly after precursor infiltration pyrolysis (PIP) treatment with 66.7%vol PF-ethanol solution twice. According to the crystal nucleation-growth theory, it was inferred that the infiltrated PF could provide a certain amount of pyrolytic carbon in the carbonized specimen. During the reaction bonded process, the carbon formed by carbonization pyrolysis first dissolves into the molten Si and reaches saturation. With the further dissolution of carbon, [C] and [Si] in the liquid phase contact each other to form β-SiC nuclei, the nuclei that precipitate at the pore wall position and gradually form a continuous interfacial layer of β-SiC. The β-SiC layer prevents the liquid Si from direct contact with C inside the prefabricated body, therefore, further reactants diffuse through the layer. Finally, the fine crystalline β-SiC grains were fabricated inside the specimen.

Preparation of Silicon Carbide/Graphite Composite Ceramic Sealing Material by Liquid Silicon Inifltration Processing

Gel casting and properties of porous silicon carbide/silicon nitride composite ceramics

PREPARATION OF TiC/SiC AND TiN/SiC COMPOSITE CERAMICS FROM LIQUID SILICON INFILTRATION

Preparation of Porous SiC Ceramic Using Bamboo Charcoal and Silica Sol As Pore-Forming Agents

Pressureless Sintering of Multilayer Graphene Reinforced Silicon Carbide Ceramics for Mechanical Seals

Preparation and characterization of porous, biomorphic SiC ceramic with hybrid pore structure

Preparation and Properties of Porous Silicon Carbide Ceramics Through Coat-Mix and Composite Additives Process

Preparation of low residual silicon content Si-SiC ceramics by binder jetting additive manufacturing and liquid silicon infiltration

Fabrication and Properties of SiC/mullite Composite Porous Ceramics

Reaction Forming of Silicon Carbide Ceramic Using Phenolic Resin Derived Porous Carbon Preform

Preparation of Porous SiC Ceramics Using Starch as Pore-forming Agent

Microstructure Evolution and Performance Improvement of Silicon Carbide Ceramics via Impregnation Method

Preparation and Properties of Porous SiC/SiC Composites

Effect of impregnated phenolic resin on the properties of Si–SiC ceramic matrix composites fabricated by SLS-RMI

Microstructure Evolution Process of Porous Silicon Carbide Ceramics Prepared Through Coat-Mix Method

Preparation of Porous Sic Ceramic with A Woodlike Microstructure by Sol-Gel and Carbothermal Reduction Processing

Preparation and mechanical behaviors of multiscale SiC nanowires/carbon fiber reinforced silicon oxycarbide ceramic composites

Fabrication and Mechanical Properties of SiCw(p)/SiC-Si Composites by Liquid Si Infiltration using Pyrolysed Rice Husks and SiC Powders as Precursors

Preparation of Complex-Shape SiC Ceramic Composites Parts Derived from Phenolic Resin Template

Thermal Conductivity and Microstructure Properties of Porous SiC Ceramic Derived from Silicon Carbide Powder

A Novel Method for the Preparation of Porous SiC