Abstract:Vat photopolymerization (VPP) 3D printing of ceramics normally uses ceramic slurries directly made of the target ceramic powder. It may become challenging when the ceramic powders are difficult-to-make and thus are expensive or rarely accessible. We have previously proposed a generative shaping and material-forming (GSM) 3D printing strategy, which involves the use of low-cost multi-component inorganic ceramic precursors as powder sources. The shaping of complex structures was realized through VPP, followed by reaction sintering to form the target ceramic material. In the current study, as a step further, ceramic (Li2CO3) and polymer (methyl polysiloxane) combined precursors were employed as an alternative material source for the first time to go through the 3D printing and reaction sintering processes, complementing the application range of the proposed GSM strategy. The slurry formulation and printability, the sinterability of the printed parts and the microstructures and mechanical performance of the sintered parts were characterized and optimized in accordance with the ingredient contents, particularly the stoichiometric ratios of Si:Li in the precursors. As a result, complex-structured Li4SiO4 ceramics with high purity were fabricated based on the use of Li2CO3 ceramic and Si-rich polymer as precursors. Through the advanced characterization and analysis of material phase and microstructural evolution, it was found that the fabricated complex-structured Li4SiO4 ceramics based on a precursor slurry with a solid content of 40 vol%, a Si:Li ratio of 1:2.5, and a sintering temperature of 850 °C showed a high phase purity of 97.23% and a compressive strength of 15.24 ± 0.33 MPa, with a skeleton’s relative density of 65.31% is achieved. The results showed greatly enhanced strength at much higher porosities, which might be advantageous and beneficial to structure engineering for mechanical enhancement and the improvement of tritium release effectiveness. Compared with the previous study using multi-component ceramic powder precursors, the ceramics prepared in this study exhibited enhanced microstructural stability and higher phase purity with an advantageously lower sintering temperature. Further analysis revealed that compared with the high temperature solid-state reaction of multi-component ceramic powder precursors, the involvement of the Si-rich polymer precursor enabled the more efficient and complete synthesis of Li4SiO4 as a result of the accelerated covering and cleavage of Si–O–Si bonds on the Li2CO3 particles at a much lower temperature. The present work suggests that the GSM strategy using combined ceramic and polymer precursors as proposed in this study is a promising alternative method to produce high quality Li4SiO4 components with complex structures.

Properties regulation of SiC ceramics prepared via stereolithography combined with reactive melt infiltration techniques

Microstructure Evolution and Performance Improvement of Silicon Carbide Ceramics via Impregnation Method

Effect of impregnated phenolic resin on the properties of Si–SiC ceramic matrix composites fabricated by SLS-RMI

Effects of carbon content on microstructure and mechanical properties of SiC ceramics fabricated by SLS/RMI composite process

Enhanced Molding and Mechanical Properties of SiC-based Ceramic Lattice Structures Via Digital Light Processing

Optimizing the properties of vat photopolymerization 3D-printed SiC ceramics by multi-infiltration

Preparation of low residual silicon content Si-SiC ceramics by binder jetting additive manufacturing and liquid silicon infiltration

Stereolithography 3D printing of SiC ceramic with potential for lightweight optical mirror

Preparation of silicon carbide ceramic slurry for stereolithography based additive manufacturing

Investigation of curing behavior and mechanical properties of SiC ceramics prepared by vat photopolymerization combined with pressureless liquid-phase sintering using Al 2 O 3 -coated SiC powder

Fabrication of high-strength Si/SiC composites with low shrinkage rates via vat photopolymerization technology and liquid silicon infiltration

Vatphotopholymerization of large-aperture high performance SiC mirror through multiphase carbon infiltration modification

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Stereolithography-based additive manufacturing of lightweight and high-strength Cf/SiC ceramics

High-strength and low-silicon SiC ceramics prepared by extrusion molding 3D printing

Generative shaping and material-forming (GSM) enables structure engineering of complex-shaped Li4SiO4 ceramics based on 3D printing of ceramic/polymer precursors

Controllable reduction of absorbance and two-step reaction for 3D-printed SiC ceramics with micron-level periodic structure

Preparation of photosensitive SiO2/SiC ceramic slurry with high solid content for stereolithography

Enhancing mechanical properties of selectively laser sintered SiC/Si composites printed using electrostatic spraying microspheres with fine particles

Additive manufacturing of SiC-Sialon refractory with excellent properties by direct ink writing