Abstract:Selective laser sintering (SLS) combined with reaction melt infiltration was used to fabricate Si–SiC ceramic matrix composites, and the effects of different concentrations of phenolic resin (PF) on the properties of the SLS green body and carbonized and final Si–SiC samples were investigated. The results showed that the impregnation with PF can increase the bulk density, reduce the porosity of the samples at all stages, and improve the mechanical properties of the reactive bonded samples. The degree of densification and mechanical properties of the sample gradually enhanced with an increase in PF concentration. The main phases of the Si–SiC composites were free Si, α-SiC, β-SiC, plus an extremely small amount of Al–Si alloy, and the SiC and the Si phase contents increased and decreased, respectively, as the concentration of PF increased when measured using Rietveld refinement and image analysis software. The macroscopic properties of the samples improved greatly after precursor infiltration pyrolysis (PIP) treatment with 66.7%vol PF-ethanol solution twice. According to the crystal nucleation-growth theory, it was inferred that the infiltrated PF could provide a certain amount of pyrolytic carbon in the carbonized specimen. During the reaction bonded process, the carbon formed by carbonization pyrolysis first dissolves into the molten Si and reaches saturation. With the further dissolution of carbon, [C] and [Si] in the liquid phase contact each other to form β-SiC nuclei, the nuclei that precipitate at the pore wall position and gradually form a continuous interfacial layer of β-SiC. The β-SiC layer prevents the liquid Si from direct contact with C inside the prefabricated body, therefore, further reactants diffuse through the layer. Finally, the fine crystalline β-SiC grains were fabricated inside the specimen.

Effects of carbon content on microstructure and mechanical properties of SiC ceramics fabricated by SLS/RMI composite process

Effects of chopped carbon fiber on the forming, structure and mechanical properties of CCF/SiC composites fabricated by SLS and RMI

The influence of carbon source and content on structure and mechanical properties of sic processed via spark plasma sintering method

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Properties regulation of SiC ceramics prepared via stereolithography combined with reactive melt infiltration techniques

Additive manufacturing of Csf/SiC composites with high fiber content by direct ink writing and liquid silicon infiltration

Effect of impregnated phenolic resin on the properties of Si–SiC ceramic matrix composites fabricated by SLS-RMI

Effect of SiC content on the mechanical behaviour of a three-dimensional needled C/SiC composite

Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic composites

Microstructure Evolution and Performance Improvement of Silicon Carbide Ceramics via Impregnation Method

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

Preparation of low residual silicon content Si-SiC ceramics by binder jetting additive manufacturing and liquid silicon infiltration

Fabrication and Property of SiC Ceramic with Large Thickness/Diameter Ratios

Fabrication and characterization of carbon fiber reinforced SiC ceramic matrix composites based on 3D printing technology

Microstructure and mechanical properties of SiC reinforced AlSi10Mg composites fabricated by laser metal deposition

Microstructure and mechanical properties of continuous carbon fiber-reinforced SiC ceramic composite fabricated by direct ink writing

Effect of diamond content on microstructure and properties of C/SiC-diamond composites

Enhanced strength and toughness of SiC/C composite ceramics via SiC@graphene core–shell nanoparticles

Effect of Carbon Black on the Microstructure and Mechanical Behaviors of Reaction Bonded Silicon Carbide Ceramics Reinforced by Chopped Fiber

Effect of the SiC powder microscopic morphology on properties of Si/SiC ceramics prepared by spark plasma sintering

Effect of laser parameters on microstructure and phase evolution of Ti-Si-C composites prepared by selective laser melting