Abstract:Aluminum nitride thin film can be applied as a high-temperature material because of its excellent heat resistance and thermal conductivity, and high mechanical strength. In addition, application and application to surface acoustic wave devices using piezoelectric properties are expected, and it is known as a material that can replace ZnO. To obtain excellent crystal orientation, the residual stress behavior inside the thin film should be fully evaluated and identified. In this study, AlN thin films were deposited by the conventional PM sputtering method and the Two-Facing-Target (TFT) PM sputtering method using BLC glass and quartz glass with different thermal expansion coefficients as substrates. In the process of cooling the fabricated thin film, the effect of the difference in the coefficient of thermal expansion with the substrate on the residual stress of the thin film and the effect of the substrate temperature on the properties of the thin-film structure and the residual stress when the thin film was deposited were investigated. The AlN thin film deposited on the glass substrate by the conventional PM sputtering method showed a crystal structure in which the c -axis was preferentially oriented in the normal direction of the substrate surface, the same as the AlN thin film produced by the two-facing-target PM sputtering method. The AlN thin film deposited on the glass substrate had a crystal structure in which the c -axis was preferentially oriented in the normal direction to the substrate, and the c -axis orientation showed excellent c -axis orientation when the substrate temperature was higher than 523 K. In the case of the quartz glass substrate, the increase of the tensile residual stress was evident as the substrate temperature increased, and the effect of the thermal residual stress was confirmed.

Effect of Gas Pressure on Residual Stresses in Aln Films Deposited on Al Substrates

Sputtering Growth of Preferential C-Axis-oriented Aluminum Nitride Film Using Homogeneous Buffer Layer

Preparation of AIN Thin Film by DC Sputtering on SiO2/Si and Analysis of Microstructure

Preparation Technique Of Aln Piezoelectric Thin Film

Influence of sputtering parameters on structures and residual stress of AlN films deposited by DC reactive magnetron sputtering at room temperature

Effects of crystal orientation, substrate type, and substrate temperature on residual stress of AlN thin films deposited by different deposition methods

Influence of Nitrogen Content and Bias Voltage on Residual Stress and the Tribological and Mechanical Properties of CrAlN Films

Minimizing residual stress of aluminum nitride (AlN) thin films using multi-step deposition of DC pulsed sputtering

Residual stress classification of pulsed DC reactive sputtered aluminum nitride film via large-scale data analysis of optical emission spectroscopy

Preparation of Aln Thin Films for Film Bulk Acoustic Resonator Application by Radio Frequency Sputtering

Residual Stress in AlN Films Grown on Sapphire Substrates by Molecular Beam Epitaxy

Study of preparation of AlN Thin Films for FBAR Application by RF Sputtering

Growth of AIN Films by RF Reactive Magnetron Sputtering for Film-Bulk-Acoustic-Wave-Resonator Fabrication

Preparation and Properties of C-axis Preferred Orientation AlN Thin Films by Pure Nitrogen Reactive Sputtering

Analysis of Residual Stress of Gradient TiAlN Films Prepared by Arc Ion Plating

Minimizing film residual stress with in situ OES big data using principal component analysis of deposited AlN films by pulsed DC reactive sputtering

Effect of gas Pressure on the Mechanical Properties of Sputtered TaN Films

Investigation of deposition parameters on the structural properties and hardness of TiAlN films deposited via reactive pulsed DC magnetron sputteringInvestigation of deposition parameters on structural properties and hardness of TiAlN films deposited by reactive pulsed DC magnetron sputtering

Deposition of c-axis orientation aluminum nitride films on flexible polymer substrates by reactive direct-current magnetron sputtering

Strain Effects on InxAl1−xN Crystalline Quality Grown on GaN Templates by Metalorganic Chemical Vapor Deposition

Strain in Alingan Thin Films Caused by Different Contents of Al and in Studied by Rutherford Backscattering/Channeling and High Resolution X-Ray Diffraction