Abstract:Chemical-mechanical planarization (CMP) represents the preferred technology in which both chemical and mechanical interactions are combined to achieve global planarization/polishing of wafer surfaces (wafer patterns from metal with a selective layer, in this paper). CMP is a complex process of material removal process by friction, which interferes with numerous mechanical and chemical parameters. Compared with chemical parameters, mechanical parameters have a greater influence on the material removal rate (MRR). The mechanical parameters manifest by friction force (Ff) and heat generated by friction in the CMP process. The Ff can be estimated by its monitoring in the CMP process, and process temperature is obtained with help of an infrared rays (IR) sensor. Both the Ff and the MRR increase by introducing colloidal silica (SiO2) as an abrasive into the selective layer CMP slurry. The calculated wafer non-uniformity (WNU) was correlated with the friction coefficient (COF). The control of Ff and of the slurry stability is important to maintain a good quality of planarization with optimal results, because Ff participates in mechanical abrasion, and large Ff may generate defects on the wafer surface. Additionally, the temperature generated by the Ff increases as the SiO2 concentration increases. The MRR of the selective layer into the CMP slurry showed a non-linear (Prestonian) behavior, useful not only to improve the planarization level but to improve its non-uniformity due to the various pressure distributions. The evaluation of the Ff allowed the calculation of the friction energy (Ef) to highlight the chemical contribution in selective-layer CMP, from which it derived an empirical model for the material removal amount (MRA) and validated by the CMP results. With the addition of abrasive nanoparticles into the CMP slurry, their concentration increased and the MRA of the selective layer improved; Ff and MRR can be increased due to the number of chemisorbed active abrasive nanoparticles by the selective layer. Therefore, a single abrasive was considered to better understand the effect of SiO2 concentration as an abrasive and of the MRR features depending on abrasive nanoparticle concentration. This paper highlights the correlation between friction and temperature of the SiO2 slurry with CMP results, useful to examine the temperature distribution. All the MRRs depending on Ef after planarization with various SiO2 concentrations had a non-linear characteristic. The obtained results can help in developing a CMP process more effectively.

Notice of Retraction Failure Mode Identification Using Thermal Data Based on Mixed Effects Model in Chemical Mechanical Planarization Process

Study on the Removal Function of Annular Polishing Pad Based on the Computer Controlled Polishing Technology

A chemical mechanical polishing model incorporating both the chemical and mechanical effects

Statistical and Experimental Analysis of Correlated Time-Varying Process Variables for Conditions Diagnosis in Chemical–Mechanical Planarization

Molecular Modeling of the Mechanical Effect in the Chemical Mechanical Polishing Process

Nonlinear Dynamics Modeling of Correlated Functional Process Variables for Condition Monitoring in Chemical–Mechanical Planarization

Modeling the microscale contact status in chemical mechanical polishing process

The Effects of Friction and Temperature in the Chemical-Mechanical Planarization Process

Modeling Chemical Mechanical Polishing with Couple Stress Fluids

A Chemical Mechanical Polishing Model Based on the Viscous Flow of the Amorphous Layer

Modeling the Chemical-Mechanical Synergy During Copper CMP

Effects of abrasive size distribution in chemical mechanical planarization: Modeling and verification

A plasticity-based model of material removal in chemical-mechanical polishing (CMP)

A Contact-Mechanics-Based Model For General Rough Pads In Chemical Mechanical Polishing Processes

Mechanical Model of Nanoparticles for Material Removal in Chemical Mechanical Polishing Process

Non-continuum Material Removal Mechanism of Surface Polishing with Ultra Precision

Energy dissipation and constitutive modeling for a mechanistic description of pad scratching in chemical–mechanical planarization

Analytical Modelling of Material Removal in Copper Chemical Mechanical Polishing Incorporating the Scratch Hardness of the Passivated Layer on Copper Thin Film Wafer

Analysis on Pad Effects in Chemical Mechanical Polishing

Material Removal Mechanism in Chemical Mechanical Polishing: Theory and Modeling

A Coupled Material Removal Model for Chemical Mechanical Polishing Processes