Abstract:Chemical-mechanical planarization (CMP) represents the preferred technology in which both chemical and mechanical interactions are combined to achieve global planarization/polishing of wafer surfaces (wafer patterns from metal with a selective layer, in this paper). CMP is a complex process of material removal process by friction, which interferes with numerous mechanical and chemical parameters. Compared with chemical parameters, mechanical parameters have a greater influence on the material removal rate (MRR). The mechanical parameters manifest by friction force (Ff) and heat generated by friction in the CMP process. The Ff can be estimated by its monitoring in the CMP process, and process temperature is obtained with help of an infrared rays (IR) sensor. Both the Ff and the MRR increase by introducing colloidal silica (SiO2) as an abrasive into the selective layer CMP slurry. The calculated wafer non-uniformity (WNU) was correlated with the friction coefficient (COF). The control of Ff and of the slurry stability is important to maintain a good quality of planarization with optimal results, because Ff participates in mechanical abrasion, and large Ff may generate defects on the wafer surface. Additionally, the temperature generated by the Ff increases as the SiO2 concentration increases. The MRR of the selective layer into the CMP slurry showed a non-linear (Prestonian) behavior, useful not only to improve the planarization level but to improve its non-uniformity due to the various pressure distributions. The evaluation of the Ff allowed the calculation of the friction energy (Ef) to highlight the chemical contribution in selective-layer CMP, from which it derived an empirical model for the material removal amount (MRA) and validated by the CMP results. With the addition of abrasive nanoparticles into the CMP slurry, their concentration increased and the MRA of the selective layer improved; Ff and MRR can be increased due to the number of chemisorbed active abrasive nanoparticles by the selective layer. Therefore, a single abrasive was considered to better understand the effect of SiO2 concentration as an abrasive and of the MRR features depending on abrasive nanoparticle concentration. This paper highlights the correlation between friction and temperature of the SiO2 slurry with CMP results, useful to examine the temperature distribution. All the MRRs depending on Ef after planarization with various SiO2 concentrations had a non-linear characteristic. The obtained results can help in developing a CMP process more effectively.

Statistical and Experimental Analysis of Correlated Time-Varying Process Variables for Conditions Diagnosis in Chemical–Mechanical Planarization

Nonlinear Dynamics Modeling of Correlated Functional Process Variables for Condition Monitoring in Chemical–Mechanical Planarization

Investigation of Dynamic Multivariate Chemical Process Monitoring

Kinematic Analysis of in Situ Measurement During Chemical Mechanical Planarization Process.

Notice of Retraction Failure Mode Identification Using Thermal Data Based on Mixed Effects Model in Chemical Mechanical Planarization Process

Statistical Feature Extraction and Hybrid Feature Selection for Material Removal Rate Prediction in Chemical Mechanical Planarization Process

An in Situ End-Point Detection System Using Motor Power Signal for Chemical Mechanical Planarization Process

Modeling and Experimental Analysis of the Material Removal Rate in the Chemical Mechanical Planarization of Dielectric Films and Bare Silicon Wafers

Analysis of Interaction Structure among Multiple Functional Process Variables for Process Control in Semiconductor Manufacturing

Phase Partition Based Virtual Metrology for Material Removal Rate Prediction in Chemical Mechanical Planarization Process

Kinematic Optimization for Chemical Mechanical Polishing Based on Statistical Analysis of Particle Trajectories

Molecular Modeling of the Mechanical Effect in the Chemical Mechanical Polishing Process

Tribology Analysis of Chemical‐Mechanical Polishing

Modeling the microscale contact status in chemical mechanical polishing process

Chemical mechanical polishing: Theory and experiment

The Effects of Friction and Temperature in the Chemical-Mechanical Planarization Process

Investigation of Material Removal Mechanism of Silicon Wafer in the Chemical Mechanical Polishing Process Using Molecular Dynamics Simulation Method

Numerical and Experimental Investigation on Multi-Zone Chemical Mechanical Planarization

A Coupled Material Removal Model for Chemical Mechanical Polishing Processes

Wear phenomena in chemical mechanical polishing

Chemical metrology methods for CMP quality