Abstract:High-textured pyrolytic carbon (PyC) is the ideal interface for SiC fiber-reinforced SiC matrix (SiCf/SiC) composites. To prepare high-textured PyC coatings on SiC fibers efficiently, chemical vapor deposition (CVD) technique was applied with the single precursor ethanol. The effects of CVD parameters on the morphology and textures of PyC were investigated in detail. Rough laminar (RL), smooth laminar (SL) and regenerative laminar (ReL) PyC could be obtained by controlling the CVD parameters. High-textured RL PyC could be stably synthesized in a large distance range in the horizontal tube furnace at 1150 °C and 10–20 kPa (total pressure), which inferred that low temperature and negative pressure were beneficial to the formation of RL PyC. Conversely, when the temperature was up to 1350 °C, the textures of PyC at different deposition positions varied considerably. In the vicinity of isothermal zone, the texture evolution of PyC with deposition positions followed the pattern of SL→RL→SL, which could be ascribed to the ratio change of the small linear hydrocarbons (fillers) and the aromatic hydrocarbons (particles) in the gas phase. The texture evolution followed the Particle-Filler model. In addition to PyC textures, the PyC coating thickness played a critical role in regulating the mechanical properties of SiC fibers and SiCf/SiC composites. In the present work, the effects of thickness of RL PyC coatings on the tensile properties of SiC fibers were investigated. The SiC fibers with 0.3 μm RL PyC coating showed the highest average tensile strength (2735 MPa) and Weilbull modulus (10.34), which might be ascribed to the repair of fiber surface defects and the appropriate stress state between fibers and coatings. The results could provide essential data for the interface design and optimization of SiCf/SiC composites.

Deposition Rate, Texture, and Mechanical Properties of Sic Coatings Produced by Chemical Vapor Deposition at Different Temperatures

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

High Temperature Oxidation Behavior of SiC Coating Materials

Microstructure and oxidation behavior of SiOC coatings on C/C composites co-deposited with HMDS and TEOS by using CVD process

Effect of deposition temperature on the corrosion behavior of CVD SiC coatings on SiCf/SiC composites under simulated PWR conditions

Comparison Study of Silicon Carbide Coatings Produced at Different Deposition Conditions with Use of High Temperature Nanoindentation

A Study of the Microstructure and Mechanical Properties of Sic Coatings on Spherical Particles

Microstructural and Tribological Properties of Cold Sprayed High Content Sicp/Al Coating by Sicp Mild-Oxidation Treatment

Growth and Mechanical Properties of Amorphous and Nanostructured SiC films

Investigation on the Electrical Properties of Vacuum Cold Sprayed SiC-MoSi 2 Coatings at Elevated Temperatures

CVD Al2O3-SiO2 compound and the mechanism investigation

Influence Of Sic Coating On The Oxidation Behavior Of Pan Carbon Fiber At Elevated Temperatures

Scheelite Coatings on SiC Fiber: Effect of Coating Temperature and Atmosphere

Effect of substrates on the characteristics of silicon carbide deposited from methyltrichlorosilane

Characterization of Silicon Carbide Films Prepared by Chemical Vapor Deposition

SiC_n/SiC Multilayer Oxidation Protective Coatings for C/C Composites Prepared by a Hydrothermal Electrophoretic Deposition Process

Texture control of pyrolytic carbon coatings and effects of coating thickness on the tensile properties of SiC fibers

Tensile Properties of Two-Dimensional Carbon Fiber Reinforced Silicon Carbide Composites at Temperatures Up to 1800 °C in Air

Mechanical properties and microstructure evolution of KD‐SA SiCf/BN/SiC CMCs oxidized at different temperatures

Influence of Liquid Evaporation on the Components of SiC High Emissivity Coating

Thermal Expansion Behavior of Carbon Fiber Reinforced Chemical-Vapor-infiltrated Silicon Carbide Composites from Room Temperature to 1400 °C