Abstract:A new sulfurization configuration is elaborated, and suitable parameters are explored for the preparation of Cu2CdSnS4 thin films. Appropriate copper content can reduce the fluctuations of bandgap and electrostatic potential in Cu2CdSnS4 thin film. The best efficiency of Cu2CdSnS4 thin film solar cell can be found over 10% efficient under the ratio of 0.83 and 590 °C sulfurization temperature. At present, Kesterite‐based thin‐film solar cells, such as Cu2ZnSnS4 solar cells, involve serious band‐tailed states, which leads to low open‐circuit voltage, thereby hindering the further improvement of device performance. In stannite‐based materials, such as Cu2CdSnS4, the substitution of Zn with Cd can effectively suppress CuCd‐related point defects and defect clusters; thus, the band‐tailing state is few, which has attracted considerable research attention. In this work, on the basis of using optimized sulfurization and optimizing ratios (Cu/Cd+Sn) and temperatures, Cu2CdSnS4 thin films can be obtained with good quality and single‐phase composition, in which the device prepared at a ratio of 0.83 and 590 °C has the highest efficiency. Defect analysis shows that the substitution of Zn with Cd can effectively reduce CuCd‐related defects and defect clusters (such as 2CuCd+SnCd) and also decrease Urbach energy, fluctuations of bandgap, and electrostatic potential compared with kesterite‐based devices. In particular, Cu2CdSnS4 thin‐film solar cell prepared under optimized conditions (the ratio of 0.83 and 590 °C) has the minimum reverse saturation current, red shift, and the maximum minority carrier diffusion length. Therefore, an efficiency over 10% Cu2CdSnS4 thin‐film solar cell is reported, which shows the highest efficiency among stannite‐based solar cells to date.

Fabrication of high-efficiency Cu 2 (Zn,Cd)SnS 4 solar cells by a rubidium fluoride assisted co-evaporation/annealing method

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

Fabrication of solar cells based on $Cu_2ZnSnS_4$ prepared from $Cu_2SnS_3$ synthesized using a novel chemical procedure

Achieving 11.95% Efficient Cu2ZnSnSe4 Solar Cells Fabricated by Sputtering a Cu-Zn-Sn-Se Quaternary Compound Target with a Selenization Process

Over 10% Efficiency Pure Sulfide Kesterite Solar Cells on Transparent Electrode with Cd-Ag Co-Alloying

Toward High Efficient Cu2 ZnSn(Sx ,Se1- x )4 Solar Cells: Break the Limitations of VOC and FF

11.5% efficient Cu 2 ZnSn(S,Se) 4 solar cell fabricated from DMF molecular solution

Preparation And Characterization Of Cu2znsns4 Thin Films And Solar Cells Fabricated From Quaternary Cu-Zn-Sn-S Target

Beyond 11% Efficient Cu2ZnSn(Se,S)(4) Thin Film Solar Cells by Cadmium Alloying

All-Layer Sputtering-Free Cu2Zn1-xCdxSnS4 Solar Cell with Efficiency Exceeding 7.5%

Efficient Cu2ZnSn(Se,S)4 solar cells with 79% fill factor using two-step annealing

Improved Performance of Electroplated CZTS Thin-Film Solar Cells with Bifacial Configuration

Co‐Evaporated CuSbSe2 Thin Films for Solar Cells

Cu2ZnSnSSe4 Solar Cells with 9.6% Efficiency Via Selenizing Cu-Zn-Sn-S Precursor Sputtered from a Quaternary Target

Benign Solutions and Innovative Sequential Annealing Processes for High Performance Cu2ZnSn(Se,S)4 Photovoltaics

Surprising Efficiency Enhancement of Cu 2 ZnSn(S,Se) 4 Solar Cells with Abnormal Zn/Sn Ratios

Over 10% Efficient Cu2CdSnS4 Solar Cells Fabricated from Optimized Sulfurization

CZTSSe solar cell with an efficiency of 10.19% based on absorbers with homogeneous composition and structure using a novel two-step annealing process

Heterojunction interface regulation to realize high-performance flexible Kesterite solar cells