Abstract:Solar cells based on kesterite-type $Cu_2ZnSnS_4$ (CZTS) thin films were fabricated using a chemical route to prepare the $CZTS$ films, consisting in sequential deposition of $Cu_2SnS_3$ (CTS) and $ZnS$ thin films followed by annealing at $550^\circ C$ in nitrogen atmosphere. The $CTS$ compound was prepared in a one-step process using a novel chemical procedure consisting of simultaneous precipitation of $Cu_2S$ and $SnS_2$ performed by diffusion membranes assisted $CBD$ (chemical bath deposition) technique. Diffusion membranes were used to optimize the kinetic growth through a moderate control of release of metal ions into the work solution. As the conditions for the formation in one step of the $Cu_2SnS_3$ compound have not yet been reported in literature, special emphasis was put on finding the parameters that allow growing the $Cu_2SnS_3$ thin films by simultaneous precipitation of $Cu_2S$ and $SnS_2$. For that, we propose a methodology that includes numerical solution of the equilibrium equations that were established through a study of the chemical equilibrium of the system $SnCl_2$, $Na_3C_6H_5O_7\cdot 2H2O$, $CuCl_2$ and $Na_2S_2O_3\cdot5H_2O$. The formation of thin films of $CTS$ and $CZTS$ free of secondary phases grown with a stoichiometry close to that corresponding to the $Cu_2SnS_3$ and $Cu_2ZnSnS_4$ phases, was verified through measurements of X-ray diffraction $(XRD)$ and Raman spectroscopy. Solar cell with an efficiency of $4.2%$, short circuit current of $16.2 mA/cm^2$ and open-circuit voltage of 0.49 V was obtained.

Preparation And Characterization Of Cu2znsns4 Thin Films And Solar Cells Fabricated From Quaternary Cu-Zn-Sn-S Target

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

Synthesis and characterization of CZTS and Cu2-xAgxZnSnS4 thin films for the application of solar cells

A Strategy to Stabilize Kesterite Czts for High-Performance Solar Cells

All-Layer Sputtering-Free Cu2Zn1-xCdxSnS4 Solar Cell with Efficiency Exceeding 7.5%

Achieving 11.95% Efficient Cu2ZnSnSe4 Solar Cells Fabricated by Sputtering a Cu-Zn-Sn-Se Quaternary Compound Target with a Selenization Process

Preparation of High-Quality Cu2ZnSnS4 Thin Films for Solar Cells Via the Improvement of Sulfur Partial Pressure Using a Static Annealing Sulfurization Approach

Preparation and Characterization of Cuins2 Thin Films for Solar Cells by Chemical Bath Deposition

Improving the efficiency of Cu2ZnSnS4 solar cells by promoting the homogeneous distribution of Sn element

Determining and Controlling the Stoichiometry of Cu2ZnSnS4 Photovoltaics: the Physics and Its Implications

Study on the Optimization of Cu-Zn-Sn-O to Prepare Cu2ZnSnS4 Thin Film via a Nano Ink Coating Method

Fabrication of Cu2SnS3 Thin Film Solar Cells Via a Sol-Gel Technique in Air

Using Cu–Zn–Sn–O Precursor to Optimize CZTSSe Thin Films Fabricated by Se Doping With CZTS Thin Films

Impact of Sol–gel Precursor Treatment with Preheating Temperature on Properties of Cu2ZnSnS4 Thin Film and Its Photovoltaic Solar Cell

Stability and Electronic Structure of Cu2znsns4 Surfaces: First-Principles Study

Study of optical and structural properties of CZTS thin films using copper capping layer and sulfurization to correct stoichiometry.

Fabrication of Cu2ZnSnS4 thin films using a ceramic quaternary target

Fabrication of solar cells based on $Cu_2ZnSnS_4$ prepared from $Cu_2SnS_3$ synthesized using a novel chemical procedure

Optical and Electrical Properties of Uniform Non-Toxic Cu2ZnSnS4 Nanocrystal and Its Application in Solar Cells

Environmentally Friendly Synthesis of Copper Zinc Tin Sulfide (CZTS) Thin Film Solar Cells: Advancing Sustainable Photo-Energy Conversion with Low-Temperature Chemical Processing

CZTSe solar cells prepared by electrodeposition of Cu/Sn/Zn stack layer followed by selenization at low Se pressure