Abstract:Quaternary chalcogenide Cu 2 CoSnS 4 (CCTS) thin films were successfully prepared by spray pyrolysis on glass substrates in varying the precursor concentration and the thiourea volume. The effects of the precursor concentration and the thiourea volume on the formation of the CCTS phase were systematically investigated by X-ray diffraction, Raman spectroscopy, Energy-Dispersive X-ray Spectroscopy. The electrical resistivity at room temperature has been measured by the four probes method. It is shown that the crystallization of the stannite CCTS phase depends on both the precursor concentration and thiourea volume. The minimum volume of thiourea required to crystallize the CCTS phase depends on the precursor concentration, i.e. the CCTS crystallization needs higher volume of thiourea at low precursor concentration. For higher precursor concentration, the CCTS is poorly crystallized with the presence of secondary phases such as CuS 2 , CoS 2 , and CuCo 2 S 4 , while the crystallization domain is relatively large. The CCTS well crystallizes only in a narrow range of precursor concentration and thiourea volume. The relatively poor crystallization combined with the presence of secondary phases are harmful for the optical and electrical features of the CCTS film. Besides, optical transmission measurements of the optimized film showed an optical gap of 1.7 eV (~ 730 nm) and an absorption coefficient included between 10 4 and 10 5 cm −1 in the visible solar range. Furthermore, the optimized stannite CCTS films are compact exhibiting a relatively rough and granular surface due to the formation of copper sulfide nodules. The electrical resistivity of the optimized CCTS film is about 0.4 10 –2 Ω cm. These results suggest that the deposited films fit the requirements of absorbing layer in solar cells. The diode composed of Au/Cu 2 CoSnS 4 /SnO 2 films was investigated with current–voltage ( I – V ) measurements performed under dark and bright conditions. The series resistance, saturation current and ideality factor of typical diode is estimated to be 689 Ω, 1.15 10 –5 A and 3, respectively.

Fabrication of Cu2SnS3 Thin Film Solar Cells Via a Sol-Gel Technique in Air

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

Fabrication of Cu2Sn1-xGexS3 Thin-Film Solar Cells via Sulfurization of Cu2GeS3/Cu2SnS3 Stacked Precursors

Fabrication of solar cells based on $Cu_2ZnSnS_4$ prepared from $Cu_2SnS_3$ synthesized using a novel chemical procedure

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

Preparation And Characterization Of Cu2znsns4 Thin Films And Solar Cells Fabricated From Quaternary Cu-Zn-Sn-S Target

Phase composition of the earth-abundant Cu2SnS3 thin films with different annealing temperature and its effects on the performance of the related solar cells

Optical and Electrical Properties Study of Sol-Gel Derived Cu2znsns4 Thin Films for Solar Cells

Impact of Sol–gel Precursor Treatment with Preheating Temperature on Properties of Cu2ZnSnS4 Thin Film and Its Photovoltaic Solar Cell

Preparation of High-Quality Cu2ZnSnS4 Thin Films for Solar Cells Via the Improvement of Sulfur Partial Pressure Using a Static Annealing Sulfurization Approach

All-Layer Sputtering-Free Cu2Zn1-xCdxSnS4 Solar Cell with Efficiency Exceeding 7.5%

Synthesis and Characterization of Hydrazine Solution Processed Cu12Sb4S13 Film

Investigation of Cu2ZnSnS4 thin film with preannealing process and ZnS buffer layer prepared by magnetron sputtering deposition

Synthesis and characterization of CZTS and Cu2-xAgxZnSnS4 thin films for the application of solar cells

In situ solvothermal growth of Cu2ZnSnS4 thin film for counter electrode of dye-sensitized solar cells

Facile synthesis of ultrafine Cu2ZnSnS4 nanocrystals by hydrothermal method for use in solar cells

Synthesis of Cu2CoSnS4 chalcogenide thin films by spray pyrolysis and efficient Au/p-CCTS/n-SnO2 diode for cells solar applications

Achieving 11.95% Efficient Cu2ZnSnSe4 Solar Cells Fabricated by Sputtering a Cu-Zn-Sn-Se Quaternary Compound Target with a Selenization Process

Effect of the stacking order, annealing temperature and atmosphere on crystal phase and optical properties of Cu2SnS3

Chemical bath deposition of SnS:Cu/ZnS for solar hydrogen production and solar cells