Abstract:Barium titanate (BaTiO3, hereafter BT) is an established ferroelectric material first discovered in the 1940s and still widely used because of its well-balanced ferroelectricity, piezoelectricity, and dielectric constant. In addition, BT does not contain any toxic elements. Therefore, it is considered to be an eco-friendly material, which has attracted considerable interest as a replacement for lead zirconate titanate (PZT). However, bulk BT loses its ferroelectricity at approximately 130 °C, thus, it cannot be used at high temperatures. Because of the growing demand for high-temperature ferroelectric materials, it is important to enhance the thermal stability of ferroelectricity in BT. In previous studies, strain originating from the lattice mismatch at hetero-interfaces has been used. However, the sample preparation in this approach requires complicated and expensive physical processes, which are undesirable for practical applications. In this study, we propose a chemical synthesis of a porous material as an alternative means of introducing strain. We synthesized a porous BT thin film using a surfactant-assisted sol-gel method, in which self-assembled amphipathic surfactant micelles were used as an organic template. Through a series of studies, we clarified that the introduction of pores had a similar effect on distorting the BT crystal lattice, to that of a hetero-interface, leading to the enhancement and stabilization of ferroelectricity. Owing to its simplicity and cost effectiveness, this fabrication process has considerable advantages over conventional methods.

Mild Hydrothermal Synthesis of Titanate Films: from Polycrystalline Batio3 to Epitaxial Pbtio3

Formation of BaTiO3 and PbTiO3 thin films under mild hydrothermal conditions

Application of Hydrothermal Mechanism for Tailor-Making Perovskite Titanate Films

Hydrothermal synthesis and characterization of lead titanate perovskite tetragonal microplates

Low-temperature synthesis of barium titanate thin films by nanoparticles electrophoretic deposition

In-situpreparation of Polycrystalline BaTiO3thin Films on Silicon by Hydrothermal Method

Hydrothermal Synthesis and Phase-, Morphology-Evolution Mechanism of Lead Titanate Nanostructures Assisted with Tetramethylammonium Hydroxide

Hydrothermal Synthesis of Single-Crystalline Perovskite PbTiO3 Nanosheets with Dominant (001) Facets

Low-temperature Preparation of BaTiO 3 Thin Film by MOD and Hydrothermal Treatment

Sol‐Gel Routes to Nanostructured Patterned Ferroelectric Thin Films with Novel Electronic and Optical Functions

A Very Low-Temperature Growth of Batio3 Thin Film by Hydrothermal Treatment Following Sol-Gel Coating at 200 Degree Celsius

Hydrothermal growth of textured Ba(x)Sr(1-x)TiO3 films composed of nanowires

Crystallization of BaTiO<sub>3</sub> Thin Films Prepared by Metalorganic Decomposition with Hydrothermal Treatment at 140°C

Hydrothermal preparation of BaTiO3 thin film on silicon

Hydrothermal BaTiO3 Thin Films on Ti‐Covered Silicon: Characterization and Growth Mechanism

Hydrothermal Synthesis and Photoluminescence of Pre-Perovskite Lead Titanate Nanofibers

Crystallization of Batio3 Thin Film at 140 Degrees C by Metalorganic Decomposition Hydrothermal Method Using Tio2 Precursor

Highly Oriented Growth of PbTiO3 Ferroelectric Nanostructure Directed by Organic Molecules under Hydrothermal Condition

Hydrothermally synthesized Pb0.70La0.30TiO3 powders

Low-temperature Crystallization of Metal Organic Decomposition BaTiO3 Thin Film by Hydrothermal Annealing

Chemical Synthesis of Porous Barium Titanate Thin Film and Thermal Stabilization of Ferroelectric Phase by Porosity-Induced Strain