Abstract:In this paper, the influences of Cr3C2/VC content on WC grain size, WC grain shape and mechanical properties of WC–6 wt. % Co cemented carbides were investigated. The results showed that the grain size first rapidly decreased and then slightly decreased with the increasing Cr3C2/VC content, and VC led to finer grain size and narrower size distribution. HRTEM/EDS analysis of the WC/Co interface indicates that the segregation concentration of V is much larger than that of Cr, which may be a strong response to the higher inhibition efficiency of VC. The addition of Cr3C2 induced triangular prism shape WC grains while VC generated stepped triangular prism grains. Despite the grain growth inhibitor (GGI) mechanisms of Cr3C2/VC have been extensively studied in the literature, the doping amount, especially the doping limit, has not been systematically investigated. In this work, the saturated solubilities of Cr and V in cobalt binder phase along with carbon content hare been predicted based on thermodynamic calculations. Based on the theoretical calculations, the doping amount of Cr3C2/VC is designed to be gradually increasing until more or less over their maximum solubilities in the binder phase, thereby investigating the subsequent microstructure and mechanical properties. When the doping of Cr3C2/VC exceeds the maximum solubility in Co phase, Co-rich Cr-carbides and Co-deficient V-carbides would form respectively, which were detrimental to the transverse rupture strength (TRS) and impact toughness. The hardness increased with the increasing Cr3C2/VC content, while the fracture toughness decreased with the increasing Cr3C2/VC content. The TRS initially enhanced and then declined, but the stepped triangular prism shape grains and low fraction of WC/Co interface in WC–6Co–VC cemented carbide led to a more pronounced decline in the TRS. The sample with 0.6 wt. % Cr3C2 addition had good comprehensive mechanical properties, its hardness, fracture toughness and TRS were 1880 kg/mm2, 9.32 MPa·m1/2 and 3450 MPa, respectively.

TEM and ToF-SIMS studies on the corrosion behavior of vanadium and chromium containing WC–Co hard metals in alkaline solutions

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Corrosion Behavior of Hvof Sprayed Hard Face Coatings in Alkaline-Sulfide Solution

Influence of Cr3C2 and VC Content on WC Grain Size, WC Shape and Mechanical Properties of WC–6.0 wt. % Co Cemented Carbides

Effects of VC/Cr3C2 on WC grain morphologies and mechanical properties of WC-6wt.%Co cemented carbides

Effects of Cr,V,Ta Additives on Electrochemical Corrosion Behaviors of Extra Coarse and Super Extra Coarse Cemented Carbides

Influence and function of inhibitor VC/Cr3C2 on the grain growth in super fine WC-Co cermets

Influence of TiC additions on the corrosion behaviour of WC–Co hardmetals in alkaline solution

Effect of Cr on the Microstructure and Oxidation Properties of Co-Al-W Superalloys Studied by in Situ Environmental TEM

Enhancing Comprehensive Properties of Hvof Thermally Sprayed Wc-10co Coatings Using Two Grain Inhibitors

Corrosion Resistance Enhancement of WC Cermet Coating by Carbides Alloying

Electrochemical Corrosion Behaviors of Binderless Carbides

Decarburization Control and Performance Enhancement: Optimizing HVOF Sprayed Submicron WC-12Co Coating with Additives

Effect of Cobalt and Chromium Content on Microstructure and Properties of WC-Co-Cr Coatings Prepared by High-Velocity Oxy-Fuel Spraying

On the Formation and Properties of Chromium Carbide and Vanadium Carbide Coatings Produced on W1 Tool Steel Through Thermal Reactive Diffusion (TRD)

Effect of (cr, V)2(C, N) on the Microstructure and Mechanical Properties of WC-10Co Cemented Carbides

Effects of Cr3C2, VC, and TaC on Microstructure, WC Morphology and Mechanical Properties of Ultrafine WC–10 wt. % Co Cemented Carbides

Investigation of Microstructures and Corrosion Resistance of Two Types of AC-HVAF Sprayed WC Coatings

Microstructure Evolution and Micro-Mechanical Behavior of Secondary Carbides at Grain Boundary in a Fe–Cr–W–Mo–V–C Alloy

Research on the Preparation Process and Performance of a Wear-Resistant and Corrosion-Resistant Coating

Electrochemical Corrosion Behaviors and Corrosion Mechanism of WC-Co Cemented Carbide in Different Aggressive Mediums