Abstract:SiC layer was prepared in an industrial scale spout fluidized bed by chemical vapor deposition. The density of SiC coating was about 3.18 g/cm(3). High temperature oxidation experiments were carried out at different temperatures from 800 to 1600 degrees C. The microstructure and composition were characterized using different methods, including mass change weighing, XRD, EDS and SEM. It was found that the weight gain of SiC coating layer was not obvious below 1200 degrees C, and subsequent mass gain gradually increased with increasing temperature, reaching 10% at 1600 degrees C. High-magnification SEM results show that the oxidation began from the surface and gradually formed punctate distribution of the oxide. Small crystal structure (similar to micron) of the SiC surface was very clear at 1000 degrees C, and this crystal structure disappeared gradually at high temperatures, forming oxides of Si in the SiC surface. There was a stacking fault stress due to the different thermal expansion coefficients and elastic modulus of SiC and Si oxides, leading to the gradual formation of cracks around the punctates. With increasing temperature, the crack further increased the oxidation rate of SiC, and finally the formed Si oxides layer fell off from the particles. It can be seen clearly that the layer was peeling when the temperature was increased to 1400 degrees C. Increasing the temperature to 1600 degrees C, the SiC coating was oxidized completely into a honeycomb structure, with obvious sintering of SiC. XRD analysis shows that there was a growing SiO2 peaks from 1400 degrees C, indicating that surface oxidation was significant. EDS results shows that the oxygen content in the coating surface gradually increased with increasing temperature. Semi-quantitative analysis shows that the surface was close to SiO2 at 1600 degrees C.

Corrosion of SiC/SiC Composite in Na2SO4 Vapor Environments from 1000 to 1500°C

Microstructure and oxidation behavior of SiOC coatings on C/C composites co-deposited with HMDS and TEOS by using CVD process

Microstructural and mechanical evolution of SiCf/SiC composites in wet oxygen atmosphere above 1000 degrees C

Corrosion behavior of precracked SiCf/SiC composites under 1200–1300°C Na2SO4‐wet‐oxygen environment

The corrosion behavior of CVD SiC coatings on SiCf/SiC composites in a simulated molten salt reactors environment

Oxidation Behavior of SiC/SiC Composites in Air at High Temperature

Corrosion behavior of CVI 2D Cf/SiC composites under high temperature burner rig tests

Mechanical Properties and Oxidation Behaviors of Self-Healing SiC F /Sic-Sibcn Composites Exposed to H 2 O/O 2 /na 2 SO 4 Environments

The impact of water and oxygen contents on the corrosion performance of yttrium silicate modified SiC f /SiC composites under high temperature conditions

The Oxidation Behavior and Corrosion Mechanism of SiC Matrix Ceramics in a High Temperature Wet Air Environment

The Corrosion Behavior of CVI SiC Matrix in SiC F /sic Composites under Molten Fluoride Salt Environment

Stress-corrosion Behavior of SiCf/SiC under CMAS-wet-oxygen Environments

Effect of deposition temperature on the corrosion behavior of CVD SiC coatings on SiCf/SiC composites under simulated PWR conditions

Oxidation and mechanical properties of SiC fibers after high temperature exposure in air and steam

Oxidation behavior of 3D SiCf/SiBCN composites at 800–1200 °C

Internal Friction Behavior Of C/Sic Composites With Environmental Barrier Coatings In Corrosive Environment

Stress‐Oxidation Behavior of a Carbon/Silicon Carbide Composite in a High‐Temperature Combustion Environment

High Temperature Oxidation Behavior of SiC Coating Materials

Corrosion behaviors of Ti3SiC2/Cu composites in molten salts

The Comparative Investigation of Oxidation Behavior and Corrosion Mechanisms of SiC Matrix Ceramics under Different Atmospheres

Comparison of Oxidation Behaviors of 3D C/PyC/SiC and SiC/PyC/SiC Composites in an O2-Ar Atmosphere