Abstract:A two-dimensional model for the simulation of solidification microstructure in multi-component alloy systems has been developed. The model is based on a cellular automaton (CA) technique for the calculation of the evolution of solid/liquid (S/L) interface. The dynamics of the interface is controlled by temperature, solute diffusion and Gibbs-Thomson effects. The diffusion equation for the temperature with release of latent heat on the S/L interface is valid in the entire domain, and the solute diffusion equation is also used in the entire domain through potential functions. Two methods are proposed to calculate the increment of the solid fraction. The first method is based on the level rule method similar to the one proposed by Jacot et al., but without the assumption of uniform temperature on the scale of the calculation domain. The second one is based on the calculation of the S/L interface velocity, which generalizes the results of Nastac and Beltran-Sanchez et al. for two-component alloy systems. If the concentration of one of the solutes tends to zero, both proposed methods reduce to the methods in Jacot et al. and Beltran-Sanchez et al. for two component alloy systems. Mesh independency is achieved by both methods and the dendritic morphologies obtained are the same if the mesh is fine enough. However, the morphologies of equiaxed dendrites calculated by using the interface velocity tends to the stable form more easily than those calculated using the level rule method as the mesh size is refined. For two-component alloy systems, the predictions of LGK theory for the steady-state tip velocity are compared with simulated values as a function of melt undercooling, which shows good agreement at very large range of undercooling. The simulated primary arm spacing in directional solidification is compared with experimental results for Fe-Si-Mg alloys and good agreement is also observed. It is noted that both methods for computing the solid fraction can be used for any multi-component alloy systems provided that the thermodynamic data are given

Determination of the Solidification Chracteristics of the A356.2 Aluminum Alloy

The solidification characteristics of 6061 and A356 aluminum alloys and their ceramic particle-reinforced composites

Determination of the Solidification Curves of Commercial Aluminum Alloys

Solidification Curves of AlCu, AlMg and AlCuMg Alloys

Experimental Investigation and Numerical Simulation of the Fluidity of A356 Aluminum Alloy

Determination of the thermophysical properties of liquid and solid Ti–6Al–4V alloy

Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys

Thermodynamic and Kinetic Calculation of High Strength Aluminum-Lithium Alloy

The Influences of the Microstructure Morphology of A356 Alloy on Its Rheological Behavior in the Semi-Solid State

Experimental determination of the phase equilibria of aluminum-rich Al−Li−Cu alloys

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

Rheologic Properties of Aluminum Alloy A356 Bille ts Produced by Semisolid Continuous Casting Process

Rheological Behavior of Semisolid A356 Alloy with Different Morphology of Primary Α Phases

A Cellular Automaton Technique for the Modeling of Solidification Microstructure in Multi-Component Alloys

Controlled Diffusion Solidification Pathway of an AA 7xxx Series Aluminum Alloy

Wettability and Interfacial Heat Transfer During Solidification of Al–Si Alloy (A413) Melt Droplets on Metallic Substrates

Microstructural Evolutions and Strengthening Mechanism according to the Aging Temperatures of a High Si Cast Aluminum Alloy

Determination of latent heats for hypoeutectic AlSi7Cu(1–4) and AlSi9Cu(1–4) alloys applying thermal analysis technique

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Calculation of Phase Diagrams and Solidification Paths of Al-rich Al−Li−Cu Alloys

Thermodynamic Description and Simulation of Solidification Microstructure in the Co-Ti System