Abstract:Aluminium silicon carbide (AlSiC) composites are silicon carbide (SiC) ceramic-reinforced aluminium matrix composites. When wide band-gap semiconductors, typically silicon carbide (SiC) and gallium nitride (GaN), work at high power density and high operating temperature, AlSiC is usually used as the thermal management material to dissipate a large amount of heat accumulated in the devices, thus reducing equipment failures caused by thermal runaway. Wetting is an important property to be considered because it can affect the heat transfer performance of AlSiC. The purpose of this work was to study the influence of 3 C-SiC crystalline orientation on the wetting behaviour of molten aluminum droplets through molecular dynamics simulation. The density distribution of Al droplets obtained on the (110) plane was stratified, while on the (111) plane, a relatively dense spindle region appeared. The physical quantities associated with the wettability of aluminium droplets on the (110) and (111) planes were also analysed. The contact angles on these two crystal planes obtained after fitting were 84.3° and 95.3°, respectively. The droplet exhibits a wetting state on the (110) plane while presenting characteristics between wetting and hydrophobicity on the (111) plane. The magnitude of the interface energy fluctuation of the (110) system was between − 17 kJ/mol and − 27 kJ/mol which was less than that of the (111) system. In the time step 2.85 × 10 5 fs before and after fitting, the average self-diffusion coefficients of aluminium droplets in the (111) system increased by 2.29 × 10 −8 and 1.9 × 10 −7 m 2 /s compared with those in the (110) system. Although it was more difficult for molten aluminium to diffuse on the (110) plane, it took longer time for the (111) system to reach stability. This further showed that the role of the 3 C-SiC crystalline orientation on droplet wettability cannot be ignored. Therefore, understanding the influence of crystal orientation on the wetting characteristics of AlSiC during its preparation is helpful for improving its heat transfer performance, and to ensure the reliable operation of wide band-gap semiconductor devices.

Wettability and Interfacial Heat Transfer During Solidification of Al–Si Alloy (A413) Melt Droplets on Metallic Substrates

Experimental Determination of the Interfacial Heat Transfer During Cooling and Solidification of Molten Metal Droplets Impacting on a Metallic Substrate: Effect of Roughness and Superheat

Experimental Investigation of Interfacial Thermal Conductance for Molten Metal Solidification on A Substrate

Isothermal Solidification of Micro Layers of Molten Aluminum Alloys

Thermal analysis and measurements for a molten metal drop impacting on a substrate: cooling, solidification and heat transfer coefficient

Spatial interfacial heat transfer and surface characteristics during gravity casting of A356 alloy

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Determination of Interfacial Heat Flux of Stainless Steel Solidification on Copper Substrate During the First 0.2 S

Numerical Simulation of Temperature Field and Grain Texture During Casting Single Crystal Superalloy DD403 with Liquid Metal Cooling

Solidification Simulation of Al-Si Alloys with Dendrite Tip Undercooling

Study on Heat Transfer Behavior at Metal/Die Interface in Aluminum Alloy Die Casting Process - I. Experimental Study and Determination of the Interfacial Heat Transfer Coefficient

Effect of Coating on Instantaneous Interfacial Heat Transfer During Near-Rapid Solidification

Interfacial Heat Transfer Behavior at Metal/die in Finger-Plated Casting During High Pressure Die Casting Process

STUDY OF INTERFACIAL HEAT TRANSFER COEFFI-CIENT BETWEEN METAL AND DIE DURING HIGH PRESSURE DIE CASTING PROCESS OF ALUMINUM ALLOY ADCl2Z

Study of the 3C-SiC surface crystalline orientation effect on the wettability of molten aluminium droplets by molecular dynamics simulation

Wetting Behavior and Interfacial Characteristics in the Molten Bi-Sn/High-Entropy Alloy System

Mechanism and Evolution of Heat Transfer in Mushy Zone During Cold Crucible Directionally Solidifying TiAl Alloys

Determination of Interfacial Heat Transfer Behavior at the Metal/Shot Sleeve of High Pressure Die Casting Process of AZ91D Alloy

Deposition of a Molten Layer of High Melting Point Material: Substrate Melting and Resolidification

Influence of heat treatment on morphology and quantity of eutectic phases of Al alloys with different cooling rates

Analysis of interfacial heat transfer coefficients in squeeze casting of AA6061 aluminum alloy with H13 steel die: Impact of section thickness on thermal behavior