Abstract:For a commercial Si(3)N(4) powder, the effects of surface modification and amount of sintering additives on rheological property of aqueous slurry were studied in this paper. High concentrated (greater than or equal to50vol%) suspension can not be prepared directly due to large amount of soluble high-valence counter-ions in the as-received Si(3)N(4) sample. Through acid-leaching and heat treatment, which eliminate the soluble counter-ions and form a silica-like layer on the particle surface, the solid loading of treated Si(3)N(4) slurry (with 5wt%Al(2)O(3)+5wt%Y(2)O(3)) has reached 50vol% with TMAH or NH(4)PA as dispersant. From DRIFT spectra, isolated Si-OH group was not detected and the amount of amine structures (Si(2)NH and SiNH(2)) was small on the original particle surface. The DRIFT pattern of acid-cleaned powder was similar to the as-received sample. However, the spectra of heated sample was considerably different from that of the as-received and acid-cleaned ones, amine structures disappeared completely and isolated Si-OH group was not induced by heat treatment. The effect of amount of oxide additives on rheological property Of Si(3)N(4) suspension was also studied in this paper. For dispersant of NH(4)PA, viscosity of 45vol% slurry was various with amount of additives and reached the lowest point at 10wt% additives. It is the influence of increasing amount of RCOO(-) adsorbed on particle surface that was substituted gradually by that of increasing concentration of Y(3+).

Dispersion Properties of Silicon Nitride Powder Coated with Yttrium and Aluminium Precursors

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Influence of powder pre-treatments on dispersion ability of aqueous silicon nitride-based suspensions

PREPARING Si3N4 CERAMICS WITH HIGH PERFORMANCES BY GELCASTING (I)INFLUENCE OF COATING Si3N4 POWDER ON MECHANICAL PROPERTIES OF THE MATERIAL

Water-Based Gelcasting of Surface-Coated Silicon Nitride Powder

Surface Characterization of Silicon Nitride Powder and Electrokinetic Behavior of Its Aqueous Suspension

The Effect of Nano-Si<sub Align=right>3n<sub Align=right>4 on Properties of Silicon Nitride Ceramics

Effects of Powder Surface Modification and Amount of Oxide Additives on Rheological Property of Si<sub>3</sub>N<sub>4</sub> Aqueous Suspension

Preparation of SiC-AlN Ceramic Alloy Powder by Direct Reaction Between Constituent Elements and Property Evaluation of Its Sintered Compacts.

Influence of α-Si3N4 coarse powder on densification, microstructure, mechanical properties, and thermal behavior of silicon nitride ceramics

Preparation of silicon carbide ceramics using chemical treated powder by DCC via dispersant reaction and liquid phase sintering

SiC-YAG Coating Microstructure Optimization Through Powder Feedstock Manufacturing Process Control

Surface Modification Of Nano-Sic Powders By Coating With Heterogeneous Nucleation Process

Preparation and properties of Si3N4 ceramics via digital light processing using Si3N4 powder coated with Al2O3-Y2O3 sintering additives

Effect of Acid Cleaning and Calcination on Rheological Properties of Concentrated Aqueous Suspensions of Silicon Nitride Powder

Aqueous Processing, Hot-Pressing and Mechanical Properties of Silicon Carbide with Al2O3 and Y2O3

Fabrication of Spherical Thermal-Conductive Silicon Nitride Powder

Coating of Y2O3 additive on Al2O3 powder and its effect on the wetting behaviour in the system Al2O3p/Al

Preparation of Si3N4 Ceramics with 3 wt % Y2O3–Al2O3 (2 : 1, 1 : 1, 3 : 5) Additions by Spark Plasma Sintering

Effect of β-Si<sub>3</sub>N<sub>4</sub> Powder on Thermal Conductivity of Silicon Nitride Ceramics

Preparation and Sintering Performance of W-Ni/Yb2O3 Composite Materials