Abstract:A series of experiments has been conducted to investigate the tribological properties of a TiN film sliding against GCr15 steel balls in ambient air, low vacuum and high vacuum environments. Various friction loads and sliding velocities were also applied. The TiN film displays a steady-state friction stage after the running-in stage in all the above environments, while the durations of running-in stages are different. The steady-state friction coefficients of the TiN film were around 0.56 in ambient air and 0.3 in the high vacuum environment (1 × 10−5 mbar). In the low vacuum (1 × 10−2 mbar) environment, a low friction coefficient (around 0.19) was attained for all the friction tests on TiN film, irrespective of the applied load and sliding velocity. In the meantime, it was noticed that the applied loads and the sliding velocities would change the duration of the running-in stage before reaching the low friction coefficient. It is revealed by the analysis of wear tracks that the metal oxides induced by the tribo-chemical effect at the friction interface play an important role in affecting the tribological behaviors of the TiN films in different environments. The Raman results show that the main component of the metal oxides is hematite (α-Fe2O3), and the amount of iron oxide is related to the friction environment. The composition and quantity of iron oxides produced by the interfacial tribo-chemical effect affect the tribological behavior. The results also show that the mechanical wear process at the friction interface displays a polishing effect, which would reduce the surface roughness. The mechanical wear performance varies under different loads and velocities. The tribological tests results indicate that the interfacial tribo-chemical effect and mechanical wear process should be considered together rather than individually to interpret the tribological behaviors of TiN films in different environments.

A Comparative-Study on Microstructure and Tribological Properties of Si3n4 and Tin Thin-Films Produced by Ibed Method

PREPARATION AND TRIBOLOGICAL PROPERTIES OF TiO2-ZrO2 THIN FILMS

A Study of the Friction and Wear Performance of MoSx Thin Films Produced by Ion Beam Enhanced Deposition and Magnetron Sputtering

Study on the friction and wear performance of MoSx thin films produced by ion-beam enhanced deposition (IBED) and magnetron sputtering (MS)

Micro/Nanotribological and Mechanical Studies of Tin Thin-Film for Mems Applications

Effect of Stress State of Different Tin Films on Their Tribological Behavior

Microstructure, Surface Morphology, and Mechanical Properties of Nanocrystalline Tin/Amorphous Si3n4 Composite Films Synthesized by Ion Beam Assisted Deposition

Effect of stress state in different TiN-films on their tribological performances

Investigation of the preparation and tribological behavior of a frictional interface covered with sinusoidal microchannels containing SnAgCu and Ti3SiC2

Microstructure, Mechanical, and Tribological Properties of Cr-Ti-Si-N Coatings

Tribological Properties of CrSiN Nanocomposite Films

Effect of Si Content on the Tribological Properties of Crsin Films in Air and Water Environments

Comparative investigation and characterization of the nano-mechanical and tribological behavior of RF magnetron sputtered TiN, CrN, and TiB2 coating on Ti6Al4V alloy

Microstructure, Mechanical and Tribological Properties of CrSiC Coatings Sliding Against SiC and Al2O3 Balls in Water

Comparison of the tribological properties of an ion sulfurized coating and a plasma sprayed FeS coating

The Tribological Behaviors of Three Films Coated on Biomedical Titanium Alloy by Chemical Vapor Deposition

Microstructure and tribological properties of sulphide coating produced by ion sulphuration

Influence of Interfacial Tribo-Chemical and Mechanical Effect on Tribological Behaviors of TiN Film in Different Environments

Study on Microstructures and Tribological Performance of Ion Plating Mo Layer

Study on the tribological characteristics of surface triangular textured TC4 alloy prepared by SLM technology

Structure and Microtribological Characteristics of Laser-Arc Deposited TiB2 Thin Film