Abstract:TiO2, SiO2, hydroxyapatite (HA), TiO2–HA and SiO2–HA thin films with good biocompatibility were grown on Ti–6Al–4V (coded as TC4) substrate by sol–gel and dip-coating processes from specially formulated sols, followed by annealing at 500°C. The chemical states of some typical elements in the target films were detected by means of X-ray photoelectron spectroscopy (XPS). High-resolution scanning electron microscopy (SEM) is applied to characterize the surface and cross-sectional morphologies of obtained films. Various phases of the films were characterized by XRD. The tribological properties of thin films sliding against an AISI52100 steel ball were evaluated on a reciprocating friction and wear tester. As a result, the target films were obtained. Compared with the TC4 substrate, all the sol–gel ceramic films are superior in resisting wear. Among all, HA film shows the best resistance while SiO2 film shows the worst wear resistance both under higher (3N) and lower load (1N). TiO2 shows a good wear resistance under lower load but higher load. Compared with TiO2, the wear resistance of the dual film TiO2–HA can be improved under 3N but deteriorated under 1N. Compared with SiO2, the wear resistance of SiO2–HA is improved both under 3N and 1N. Compared with HA, the wear resistances of dual films are deteriorated both under 3N and 1N. Under 0.5N, a very long wear life for TiO2–HA is also obtained, illustrating that the lower wear resistance of dual films is closely related to the applied load. SEM observation of the morphologies of worn surfaces indicates that the wear of TC4 is characterized by abrasive wear. Differently, abrasion, plastic deformation and micro-crack dominate the wear of ceramic films. The superior friction reduction and wear resistance of HA films are greatly attributed to the slight plastic deformation of the film. Sol–gel is a potential method being applied to implant materials for wear protection according to proper process designs. The single HA film and the dual TiO2–HA film is suggested for biomedical application from the point of view of wear protection.

The Tribological Behaviors of Three Films Coated on Biomedical Titanium Alloy by Chemical Vapor Deposition

Tribological behavior of different films on Ti-6Al-4V alloy prepared by plasma-based ion implantation

Different tribological behaviors of titanium alloys modified by thermal oxidation and spraying diamond like carbon

Tribological study of lubricious DLC biocompatible coatings

Tribological Behavior of Diamondlike Carbon Film-Deposited Ti6al4v Alloy Swinging Against Ultrahigh Molecular Weight Polyethylene in Fetal Bovine Serum

Mechanical and Unlubricated Tribological Properties of Titanium-Containing Diamond-Like Carbon Coatings

Tribological Behavior of TiC/DLC Multilayers Prepared on Ti–6Al–4V Alloy by Plasma-Based Ion Implantation

Improvement of Tribological Behaviour of Biomedical Nanocrystalline Titanium by Magnetron Sputtered DLC/SiC Double Layer Films

Tribological Performance of Metal Doped Diamond-like Carbon Films Deposited on CoCrMo Alloy

Study on Failure Mechanisms of Dlc Coated Ti6al4v and Cocr under Cyclic High Combined Contact Stress

Friction and wear study of diamond-like carbon gradient coatings on Ti6Al4V substrate prepared by plasma source ion implant-ion beam enhanced deposition

The Appraisal of Biotribological Properties of DLC Gradient Film on Titanium Alloy Substrate

Tribological Behaviors of Single and Dual Sol–gel Ceramic Films on Ti–6Al–4V

Tribological Properties of TiN/diamond and TiAlN/diamond Bilayer Films Sliding Against Carbon Steel

Microstructure, Tribological and Cutting Performance of Ti-DLC/α-C:H Multilayer Film on Cemented Carbide

Microstructure, mechanical and tribological properties of multilayer Ti-DLC thick films on Al alloys by filtered cathodic vacuum arc technology

Improving the Protective Properties of an Artificial Joint Friction Couple by Using TiN and DLC Films

Study on the Tribological Properties of Hard Films Deposited on Biomedical NiTi Alloy

Tribological and Biological Behaviors of Laser Cladded Ti-based Metallic Glass Composite Coatings

Structure and mechanical properties of Ti alloyed DLC films

Tribological Property Analyses of Dlc Films on Ceramic Ball Surfaces with 3-D Fea Method and Experiments