Abstract:TiO2, SiO2, hydroxyapatite (HA), TiO2–HA and SiO2–HA thin films with good biocompatibility were grown on Ti–6Al–4V (coded as TC4) substrate by sol–gel and dip-coating processes from specially formulated sols, followed by annealing at 500°C. The chemical states of some typical elements in the target films were detected by means of X-ray photoelectron spectroscopy (XPS). High-resolution scanning electron microscopy (SEM) is applied to characterize the surface and cross-sectional morphologies of obtained films. Various phases of the films were characterized by XRD. The tribological properties of thin films sliding against an AISI52100 steel ball were evaluated on a reciprocating friction and wear tester. As a result, the target films were obtained. Compared with the TC4 substrate, all the sol–gel ceramic films are superior in resisting wear. Among all, HA film shows the best resistance while SiO2 film shows the worst wear resistance both under higher (3N) and lower load (1N). TiO2 shows a good wear resistance under lower load but higher load. Compared with TiO2, the wear resistance of the dual film TiO2–HA can be improved under 3N but deteriorated under 1N. Compared with SiO2, the wear resistance of SiO2–HA is improved both under 3N and 1N. Compared with HA, the wear resistances of dual films are deteriorated both under 3N and 1N. Under 0.5N, a very long wear life for TiO2–HA is also obtained, illustrating that the lower wear resistance of dual films is closely related to the applied load. SEM observation of the morphologies of worn surfaces indicates that the wear of TC4 is characterized by abrasive wear. Differently, abrasion, plastic deformation and micro-crack dominate the wear of ceramic films. The superior friction reduction and wear resistance of HA films are greatly attributed to the slight plastic deformation of the film. Sol–gel is a potential method being applied to implant materials for wear protection according to proper process designs. The single HA film and the dual TiO2–HA film is suggested for biomedical application from the point of view of wear protection.

PREPARATION AND TRIBOLOGICAL PROPERTIES OF TiO2-ZrO2 THIN FILMS

Tribological behavior of sol–gel TiO2 films on glass

Tribological Properties of Sol Gel TiO 2 Thin Fil

Preparation and Tribological Investigation of PbS-TiO2 Nanocomposite Thin Films

Tribological Investigations of Sol-Gel Ceramic Films

Characterization and tribological investigation of sol-gel Al2O3 and doped Al2O3 films

Research on the Preparation of Zirconia Coating on Titanium Alloy Surface and Its Tribological Properties

Corrosion and Tribological Behavior of ZrO2 Films Prepared on Stainless Steel Surface by the Sol-Gel Method

Characterization and tribological investigation of sol–gel ceramic films on Ti–6Al–4V

Atomic Layer Deposition of Zinc Oxide Films: Effects of Nanocrystalline Characteristics on Tribological Performance

Tribological Behaviors of Single and Dual Sol–gel Ceramic Films on Ti–6Al–4V

Tribological Behavior And Wear Mechanism Of Ti/Mos2 Films Deposited On Plasma Nitrided Cf170 Steel Sliding Against Different Mating Materials

Preparation And Tribological Performance Of Ionic Liquid Films On Various Substrates

Study on Plasma Sprayed 40%Zro_2-Al_2o_3-13%tio_2 Ceramic Coatings and Tribological Properties

Study on Preparation and Tribological Properties of Epoxy Resin/Sio2 Hybrid Thin Film

Influence of Interfacial Tribo-Chemical and Mechanical Effect on Tribological Behaviors of TiN Film in Different Environments

Preparation and characterization of wear resistant TiO layer on Ti alloy

Preparation and characterization of TiO2, ZnO, and TiO2/ZnO nanofilms via sol–gel process

The Preparation and the Friction and Wear Behaviours of Tio2/Cnt/Pi Composite Film

Preparation and investigation of the tribological behavior of poly(phthalazinone ether ketone)/silica thin films

Characterization and Tribological Investigation of Al2O3 and Modified Al2O3 Sol-Gel Films