Abstract:Nanometer-sized particles, for example, TiO2, have gradually gained the attention to improve the mechanical and tribological properties of epoxy composite coatings. In the present paper, TiO2 with the size of 300 nm was applied to improve the reciprocating friction and wear performances of an epoxy composite. The effects of TiO2 content and sample preparation methods on the mechanical and tribological performances were investigated experimentally. It was found that the optimal mixture ratio of TiO2 was 4 wt%, and the tensile strength of composite increased by up to 30% compared with the control sample. The TiO2 nanoparticles were treated with polyvinylpyrrolidone (PVP) and then mixed into epoxy resin with three-roll mill grinding technique. The PVP molecules could surround a single TiO2 to form super-monomer, which produced repulsive force to aim to disperse nanoparticles, and the three-roll mill grinding could utilize the compression of axis surfaces and friction at different speeds to reduce the size of agglomerations of more than 5 microns. The results showed that the PVP molecules treatment could improve tensile strength and modulus, and three-roll mill grinding technique could enhance the elongation at break. In addition, the reciprocating wear rate and frictional coefficient of the epoxy composite plates also were reduced remarkably owing to the pretreatment of TiO2 particles, for example, and the frictional coefficient of epoxy composite decreased from 0.09 to 0.04 for the optimal ratio of TiO2, and special wear rate also decreased by 87.5% compared with the control sample. This was because the TiO2 nanoparticles acted as the stress transfer medium and could undertake part of loading to relieve stress directly into the epoxy matrix. There was a thin transfer film in which the particles acted as a membrane skeleton to avoid matrix further being torn. Because of the hardness and nanoeffect of particles, TiO2 could fill the defects in the wear interface to form a protective film and improve surface fatigue resistance property. The more uniform dispersion of TiO2 particles brought about the obvious improvement of wear resistance of composites.

Improved tribological and thermo‐mechanical properties of epoxy resin with micro‐nano structured ZrO 2 / Ti 3 C 2 particles

Investigation on Tribological and Thermo-Mechanical Properties of Ti 3 C 2 Nanosheets/Epoxy Nanocomposites

Enhanced Mechanical and Tribological Properties of Epoxy Composites Reinforced by Novel Hyperbranched Polysiloxane Functionalized Graphene/ MXene Hybrid

Superior Tough, Highly Wear Durable and Self-Lubricating Epoxy Composite Co-Enhanced by Soft and Hard Nanomaterials

Tribological Performance of In-Situ Epoxy Composites Filled with Micro-Sized ZrB 2 Particles

Effects of Nanotube Dispersion on Tribological Behavior of Multi-walled Carbon Nanotube/Epoxy Resin Composite

Reciprocating Friction and Wear Performances of Nanometer Sized‐tio2 Filled Epoxy Composites

Tribological Properties of Organic Functionalized ZrB 2 –Al 2 O 3 /Epoxy Composites

A synergistic effect of nano-Tio2 and graphite on the tribological performance of epoxy matrix composites

Mechanical and tribological properties of microparticulate and nanopaticulate reinforced polymer composites

Microstructure and Tribological Behavior of Polymeric Nanocomposites

Excellent tribological properties of epoxy—Ti 3 C 2 with three-dimensional nanosheets composites

Tribological properties of differently shaped zinc‐based metal‐organic framework particles reinforced epoxy resin composites

Epoxy nanocomposites with high mechanical and tribological performance

Development of Tribologically Optimized Surface Coatings with Micro and Nano Particles

Tribological Properties of Surface Modified Nano-Alumina/epoxy Composites

Improvement of Tribological Performance of Epoxy by the Addition of Irradiation Grafted Nano-Inorganic Particles

Study on tribological properties of epoxy resin composites

Preparation and Performance Study of Nano-Ti-MWCNT Hybrid Filler Reinforced Epoxy Resin Composite Coating

Mechanical, Bonding and Tribological Performances of Epoxy‐based Nanocomposite Coatings with Multiple Fillers

Construction of a binary architecture of flower-like nickel phyllosilicate@zinc sulfide towards the robust, wear-resistant and thermal-stable epoxy nanocomposites