Abstract:Wafer bonding technology is important for most MEMS devices' packaging, especially for RF-MEMS devices. Different materials systems, such as Au-Sn, Au-In, have been developed for wafer bonding. A new bonding system, using Ag-Sn, is investigated in this paper. Comparing to well developed Au-Sn bonding (typically bonding temperature of 280degC ), Ag-Sn would provide a potentially lower temperature, lower cost wafer-level bonding method. Both cap wafer and bottom wafer were sputtered with thin film Ti/Ni. Ti is the adhesion layer, and Ni is the wettability and barrier layer. Sn/Au was evaporated on Ti/Ni for cap wafer. The cap wafer was patterned by lift-off process. Ag was sputtered on Ti/Ni for bottom wafer. The thickness of Sn and Ag was designed based on the composition ratio of Ag3Sn in the bonding layer. Thin Au film could protect Sn from oxidation. Afterwards the cap wafer and substrate wafer were brought into contact and sent into the bonding machine. Bonding process was performed in a nitrogen environment. Different bonding parameters such as bonding force, bonding temperature, dwell time are studied. During bonding, the Sn melted when the temperature reached the melting point of Sn and the liquid Sn broke up the barrier layer of the intermetallic compound of Au and Sn. Then the liquid Sn wetted and dissolved the Ag layer to form the intermetallic compound Ag3Sn. The growth of such an interfacial Ag3Sn intermetallic compound is a liquid-solid diffusion process. The main compositions of the bonding interface are pure Ag and Ag3Sn intermetallic compound, which was investigated by SEM and ED AX. Shear strength of the as-bonded structure and those after reliability tests were measured by a shear force tester. The reliability tests include pressure cooker test (PCT) and thermal cycling test (TCT). It has been concluded that the Ag- Sn bonding with delicately designed bonding process one of the potential methods for wafer- bonding.

Au-Si Eutectic Bonding Technology for MEMS Device

Investigation of Au/Si Eutectic Wafer Bonding for MEMS Accelerometers

Wafer Lever Packaging for Gyroscope by Au/Si Eutectic Bonding

Study of low temperature eutectic bonding process for MEMS hermetic package

Electrical interconnect in MEMS/NEMS devices by Au/a-Si eutectic reaction

Developing Trend of Bonding Technology for MEMS

Discussion and Analysis of Au/a-Si Contact Resistance in MEMS/NEMS Devices.

Mechanism and Process of Cu-Sn Bonding for Wafer Level MEMS Packaging

Microstructure of AuSn Wafer Bonding for RF-MEMS Packaging

Evaluation of Au/a-Si eutectic wafer level bonding process

Ag-Sn Fluxless Wafer Bonding Technology

Patterned Al-Ge Wafer Bonding for Reducing In-Process Side Leakage of Eutectic.

Low Temperature Al Based Wafer Bonding Using Sn As Intermediate Layer

Low Temperature Au-In-Au Metallic Bonding and Its Application in the Fabrication of Vcsels

Au-Si Eutectic Wafer Bonding Mechanism Analysis and a Intensity Model

A New Test Structure To Measure Bonding Strength In Micro-Bonding Area

Progress in wafer bonding technology towards MEMS, high-power electronics, optoelectronics, and optofluidics

Low Temperature Au/Sn Solid-Liquid Diffusion Chip-to-Chip Bonding for MEMS Encapsulation

Technique and Structure for Testing Bonding Intension in Micron Scale

Low Temperature Eutectic Alloy Bonding Used in MEMS-Based Solid Propellant Microthrusters Array

Room Temperature Bonding of Si and Si Wafers by Using Mo/Au Nano-Adhesion Layers