Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

Fabrication and Characterization of Sic Rod-Particulate-Reinforced Reaction-Bonded Si3n4 Composites

Low Volume Fraction in Situ (ti5si3+ti2c)/ti Hybrid Composites with Network Microstructure Fabricated by Reaction Hot Pressing of Ti–SiC System

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Densification and Enhancement of Sic Particulate Reinforced Fine Grain Sic Ceramic

Silicon oxycarbide composites reinforced with silicon nitride and in situ formed silicon carbide.

Fabrication of SiC whisker reinforced laminated Si3N4/BN ceramics by spark plasma sintering

Fabrication of Si3n4/Sic Nanocomposites by Spark Plasma Sintering of Amorphous Sicn Powders Derived from A Polymeric Precursor

Preparation of SiC-AlN Ceramic Alloy Powder by Direct Reaction Between Constituent Elements and Property Evaluation of Its Sintered Compacts.

Fabrication and performance of SiC-reinforced Cu: Role of the aspect ratio of the SiC reinforcement phase

Preparation of the Rod-Like Β-Si3n4 Particles Favoring the Self-Reinforcing Si3N4 Ceramics

Synthesis of SiC-AlN Ceramic Alloy Powder by the Direct Reactions Between the Constituent Elements.

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Fabrication and Mechanical Properties of SiCw(p)/SiC-Si Composites by Liquid Si Infiltration using Pyrolysed Rice Husks and SiC Powders as Precursors

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Sintering And Mechanical Properties Of Aln-Rich Ceramics In The Sic-Aln System

Fabrication of Reaction-Sintered SisN_4 Ceramic Microrotors

Fabrication and Properties of SiO2-BN-Si3N4 Composites

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Preparation of the rod-like {beta}-Si{sub 3}N{sub 4} particles favoring the self-reinforcing Si{sub 3}N{sub 4} ceramics