Abstract:Abstract There are significant challenges for materials in extreme environments for a variety of applications such as aircraft engines, gas turbines, nuclear reactors, reentry vehicles, and hypersonic structures. Ceramic matrix composites (CMCs) could be ideal candidates to meet these stringent requirements for materials due to their high melting temperatures, high oxidation, corrosion and ablation resistance, low creep, and thermal cycling behavior in such extreme environments. Particularly, continuous fibers can bridge cracks in CMCs and therefore improve the strength and fracture toughness of composites. CMCs are traditionally manufactured by the melting infiltration method. With this method, the high porosity and brittle structure of fabricated CMCs are not capable of withstanding high mechanical and thermal loads. Alternatively, polymer derived ceramic composites are fabricated by incorporating carbon fibers into polymer derived ceramic matrix to achieve high fracture toughness. With the aid of protective coatings with metallic or ceramic materials, such as Nickel and boride nitride, carbon fiber could potentially withstand high temperatures without oxidation. In this study, continuous fiber reinforced silicon oxycarbide composite was manufactured with polysiloxane (PSX) resin and woven carbon fabrics through the polymer infiltration and pyrolysis process (PIP). Re-infiltration of the PSX resin into the composites, curing in an autoclave, and pyrolysis for additional 2 to 10 cycles can increase the yield of ceramics of the composites. A dense structure of the composites was observed by SEM. The EDS results showed that the elemental composition of the composites mainly consisted of carbon, silicon and oxygen. The crystalline structure of the composites was examined through XRD to indicate the degree of polymer pyrolysis to ceramics. The results of four-point bending testing of the composites showed a flexural strength of 62.17MPa, a flexural modulus of 51.30GPa, and a fracture toughness of 1.3 × 108J/m3.

Mechanical properties and high temperature failure mechanism of carbon fibers reinforced polysilazane-derived SiCN ceramic matrix composites via PIP process

Properties of Carbon Nano-Tubes–cf/sic Composite by Precursor Infiltration and Pyrolysis Process

High-temperature tensile behavior of 3D SiC/SiC composites

Residual stress and interface debonding behavior in Si3N4w reinforced SiCN composites prepared by the PIP process: A case study

Preparation and properties of Ti3SiC2 preform reinforced SiC ceramic matrix composites

Processing and Characterization of Continuous Carbon Fiber Reinforced Silicon Oxycarbide Ceramic Matrix Composites

High strength C/Si‒Ni‒C composites fabricated by reaction melt infiltration with Si‒Ni alloy at lower temperature

Cf/SiC Ceramic Matrix Composites with Extraordinary Thermomechanical Properties up to 2000 °C

Oxidation behavior of 3D SiCf/SiBCN composites at 800–1200 °C

Preparation of SiC fiber-reinforced SiC composites

Preparation and mechanical behaviors of multiscale SiC nanowires/carbon fiber reinforced silicon oxycarbide ceramic composites

Mechanical Properties of Si3N4/BN Fibrous Monolithic Ceramics at Elevated-Temperature

Microstructure and mechanical properties of 3D Cf/SiBCN composites fabricated by polymer infiltration and pyrolysis

Influence of Oxidation Damages on Mechanical Properties of SiC/SiC Composite Using Domestic Hi-Nicalon Type SiC Fibers

Advanced Fabrication Method and Mechanical Properties of Silicon Nitride/Boron Nitride Fibrous Monolithic Ceramics

A Modified Iosipescu Method to Study In-Plane Shear Strength of C/SiC Composites at Elevated Temperatures in Air

High temperature bending properties and failure mechanism of 3D needled C/SiC composites up to 2000 °C

A Review on High-Performance SiC f /SiC Composites Prepared by PIP Process

Tensile Mechanical Behavior and Failure Mechanism of a Plain-Woven SiCf/SiC Composites at Room and Elevated Temperatures

Preceramic Paper-Derived SiCf/SiCp Composites Obtained by Spark Plasma Sintering: Processing, Microstructure and Mechanical Properties

Influence of pyrolytic carbon interphase and pyrolysis temperature on the mechanical and tribological properties of Cf/SiC after heat treatment at 1800 °C