Abstract:In this paper, fully dense Si3N4/SiC nano-composites were fabricated through polymer-derived ceramics (PDCs) method and spark plasma sintering technique. Polymer-derived SiAlCN ceramic was synthesized by using polysilazane as preceramic precursor, aluminum tri-sec-butoxide as Al source. Then Si3N4/SiC composites with nanometer sized Si3N4 and SiC phases were formed spontaneously during spark plasma sintering through in-situ phase separation of amorphous SiAlCN ceramics. It's found that with the increasement of Al contents, the densification rate was accelerated significantly and serious degradation of Si3N4 phase was avoided by restricting carbothermal reaction. At the same time, Al contained composites show excellent oxidation/corrosion resistance at 1350 °C and 50% H2O - 50% O2 water vapor environment than that of Al free samples. The Si3N4/SiC composites derived from Al contained PDCs overcomes the trade-off between abnormal grain growth and serious degradation of Si3N4 phase, which is a very tough problem for traditional PDC route (without Al) to fabricate Si3N4/SiC composites. For traditional PDC route, (I) if with traditional sintering additives, abnormal grain growth occurs, nano grains cannot be achieved; (II) if without traditional sintering additives, serious degradation of Si3N4 occurs, Si3N4 and SiC composite cannot be formed. Therefore, Al contained polymer-derived ceramics route opens a promising avenue to fabricate Si3N4/SiC nano-composites with fine grain size, uniform microstructure and excellent oxidation/corrosion resistance.

[Forum on tissue expansion. Tissue expansion and radiotherapy. Changes in epidermal mitotic index induced by expansion and/or irradiation in the rat].

DIURNAL VARIATION IN SYSTOLIC TIME INTERVAL

Fabrication, microstructure, and properties of SiC/Al4SiC4 multiphase ceramics via an in-situ formed liquid phase sintering

Cf/SiC Ceramic Matrix Composites with Extraordinary Thermomechanical Properties up to 2000 °C

Porous SiC ceramic obtained by spark plasma sintering of preceramic paper: Microstructure, mechanical properties and gas permeability

Enhanced strength and toughness of SiC/C composite ceramics via SiC@graphene core–shell nanoparticles

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

Fast fabrication of SiC particulate-reinforced SiC composites by modified PIP process using spark plasma sintering – effects of green density and heating rate

Microstructure and mechanical properties of spark plasma sintered SiC ceramics aided by B4C

Slurry‐impregnating hot‐press sintered silicon carbide nanofiber/silicon carbide composites with Al‐B‐C as sintering additives

Interfacial microstructure and sintering mechanism of plasma activated sintered Al/SiC composites

The dynamic properties of SiCp/Al composites fabricated by spark plasma sintering with powders prepared by mechanical alloying process

Fabrication of dense Cf/SiC ceramic matrix composites using 3D printing and PIP with short carbon fibre as a toughening material

Mechanical properties and microstructure of laminated Si3N4+SiCw/BN+Al2O3 ceramics densified by spark plasma sintering

Preparation and mechanical behaviors of multiscale SiC nanowires/carbon fiber reinforced silicon oxycarbide ceramic composites

Fabrication and Mechanical Properties of SiCw(p)/SiC-Si Composites by Liquid Si Infiltration using Pyrolysed Rice Husks and SiC Powders as Precursors

In situ formation of Si3N4–SiC nanocomposites through polymer-derived SiAlCN ceramics and spark plasma sintering

Fabrication and mechanical evaluation of SiC–TiC nanocomposites by SPS

Structure and Properties of Spark Plasma Sintered SiC Ceramics with Oxide Additives

Effects of chopped carbon fiber on the forming, structure and mechanical properties of CCF/SiC composites fabricated by SLS and RMI

Rare earth monosilicates as oxidation resistant interphase for SiCf/SiC CMC: Investigation of SiCf/Yb2SiO5 model composites