Abstract:Silicon carbide (SiC) is an effective material for high-temperature engineering applications owing to its desirable properties such as high elastic modulus, high hardness, and melting temperature, high thermal conductivity, good corrosion and oxidation resistance, low density, and coefficient of thermal expansion compared with other advanced ceramics. Nevertheless, poor sinterability and low toughness limit its use, which can be overcome using appropriate additives. In this study, the effect of different amounts of nano-β-SiC (0, 5, 10, and 15 wt.%) and graphene (0, 1, 2, and 3 wt.%) particles on the sinterability behavior and microstructure of SiC composite has been investigated. After weighing, dispersing nano-β-SiC and graphene, and mixing the starting materials, milling was carried out at 180 rpm for 3 h. The materials obtained were then compressed uniaxially under a pressure of 75 MPa and then were compressed again through CIP under 150 MPa. To remove volatile products, the pyrolysis process was performed at 800 °C under Ar atmosphere. Finally, the samples were sintered at 2200 °C for 2 h by the pressureless sintering process. XRD analysis was used to investigate the phases and FESEM images were used to study the microstructure. According to the XRD patterns, β-SiC particles were converted to α-SiC, which was accompanied by the elongation of SiC grains. Also, no reaction was observed between graphene and the SiC matrix. According to the FESEM images, the samples containing 5 wt.% nano-β-SiC and 1 wt.% graphene showed a uniform distribution of reinforcement particles but with increasing the amount of the reinforcement particles, agglomeration was observed. According to the results, upon increasing the nano-β-SiC up to 5 wt% and graphene up to 1 wt.%, all the measured properties including relative density, and linear shrinkage improved and reached 99.04%, and 18.01%, respectively. However, with increasing the additives, these properties deteriorated due to increasing porosity and agglomeration in the composite structure.

Slurry‐impregnating hot‐press sintered silicon carbide nanofiber/silicon carbide composites with Al‐B‐C as sintering additives

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Aqueous Processing, Hot-Pressing and Mechanical Properties of Silicon Carbide with Al2O3 and Y2O3

Fabrication, microstructure, and properties of SiC/Al4SiC4 multiphase ceramics via an in-situ formed liquid phase sintering

Study on the Performance for Silicon Carbide Ceramics by Hot-pressing Sintering

Effects of Sintering Additives on Microstructure and Properties of Porous SiC Ceramics with High Porosity

B4C-SiC composites with tuneable mechanical properties: Role of Al2O3 - Y2O3 sintering additives

Preceramic Paper-Derived SiCf/SiCp Composites Obtained by Spark Plasma Sintering: Processing, Microstructure and Mechanical Properties

Sintering temperature-microstructure-property relationships of alumina matrix composites with silicon carbide and silica additives

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Structure and properties of fine diameter continuous SiC ceramic fiber reinforced Al matrix composites

Microstructure, phase compositions and mechanical properties of slip cast sintered SiC/Si3N4 composites

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Pressureless sintering of SiC matrix composites reinforced with nano-β-SiC and graphene

Microstructure and mechanical properties of SiC-Al2O3 nanocomposite prepared by surface modified SiC nanopowders

In situ formation of Si3N4–SiC nanocomposites through polymer-derived SiAlCN ceramics and spark plasma sintering

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Pressureless Sintering and High-Temperature Strength of SiC-AlN Ceramics

Si3N4-SiC ceramic nanocomposites

Fabrication and characterization of SiC/Al composites prepared by laser powder bed fusion (LPBF) combined with vacuum pressure infiltration

PRESSURELESS SINTERING OF SILICON CARBIDE NANOCOMPOSITE CERAMICS