Abstract:The AlN/BN composite ceramic, fabricated via hot-press sintering, exhibits obvious anisotropy due to the establishment of directional alignment of h-BN. However, the variation and influence mechanisms of bending strength (σ) and thermal conductivity (λ) are remain unclear in different directions, which greatly limit the application of AlN/BN composite ceramics. In this paper, the effects of h-BN content on phase composition, microstructure and anisotropy of AlN/BN composite ceramics are discussed in detail. The results reveal that AlN/BN composite ceramics have three directions: perpendicular (⊥), longitudinal parallel (∥), and lateral parallel (≡) to the hot-pressing direction. The content of h-BN is a crucial factor affecting the anisotropy of AlN/BN composite ceramics. h-BN enhances the thermal conductivity in the ∥ and hinders the thermal conductivity in the ⊥. With the increase in h-BN amount, λ∥ rises gradually, while λ⊥ gradually falls. When the mass percentage of h-BN and AlN is 25 % (AB25), the λ∥ is as high as 90 W m−1 K−1, which is about 2.25 times that of λ⊥. In terms of mechanical properties, σ ≡ and σ ⊥ first increase and then decrease, while σ ∥ only decreases. This is attributable to h-BN being effective in enhancing mechanical properties by inhibiting crack propagation in the ⊥ and ≡ direction, while the promotion of crack propagation leads to a decrease in mechanical properties in the ∥ direction. σ ≡ reaches the highest values (σ ≡ = 460.2 MPa) at an h-BN amount of 10 % (AB10), which is about 1.19 and 2.04 times that of σ ⊥ and σ ∥, respectively, and 22.1 % higher than that of AB0.

Effect of Boron Nitride Addition on Densification, Microstructure, Mechanical, Thermal, and Dielectric Properties of β-SiAlON Ceramic

Improved thermal shock and oxidation resistance of β-SiAlON incorporated with h-BN

Exploration of an atomic‐scale boron additive in SiAlON ceramics

Boron Nitride Doped Transparent Polycrystalline Silicon Nitride Ceramics

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Influence of hBN content on mechanical and tribological properties of Si3N4/BN ceramic composites

Microstructure and room/elevated-temperature mechanical properties of hot-pressed h-BN composite ceramics with La2O3-Al2O3-SiO2 addition

Pressureless solid-state sintering of SiC ceramics with BN and C additives

Effect of hexagonal boron nitride content on the anisotropy of hot-press-sintered AlN/BN composite ceramics

Effects of h-BN addition on microstructures and mechanical properties of β-CaSiO3 bioceramics

Flexural strength, thermal and dielectric properties of AlN ceramics with BN nanoplatelets addition

Preparation and Properties of BN-SiO<sub>2</sub> Composite Ceramics

Improvement in mechanical properties in AlN-h-BN composites with high thermal conductivity

Microstructural evolution of h-BN matrix composite ceramics with La-Al-Si-O glass phase during hot-pressed sintering

EFFECT OF h-BN AS AN ADDITIVE ON PHYSICAL AND MECHANICAL PROPERTIES OF Al2TiO5 COMPOSITE

Effects of h‐BN on the thermal shock and oxidation resistance of SiO2‐bonded SiC refractories

Influence of sintering atmosphere and BN additives on microstructure and properties of porous SiC ceramics

Fabrication and Mechanical Properties of Boron Nitride Nanotube Reinforced Silicon Nitride Ceramics

Effect of B2O3 Addition on Low-temperature Sintering Behavior and Properties of SiC/h-BN Multiphase Ceramics

Examination of milled h-BN addition on sintered Si3N4/h-BN ceramic composites