Abstract:High-quality hole-transport layers (HTLs) with excellent optical and electrical properties play a significant role in achieving high-efficient and stable inverted planar perovskite solar cells (PSCs). In this work, the optoelectronic properties of Cu-doped NiOx (Cu:NiOx) films and the photovoltaic performance of PSCs with Cu:NiOx HTLs were systematically studied. The Cu-doped NiOx with different doping concentrations was achieved by a high-temperature solid-state reaction, and Cu:NiOx films were prepared by pulsed laser deposition (PLD). Cu+ ion dopants not only occupy the Ni vacancy sites to improve the crystallization quality and increase the hole mobility, but also substitute lattice Ni2+ sites and act as acceptors to enhance the hole concentration. As compared to the undoped NiOx films, the Cu:NiOx films exhibit a higher electrical conductivity with a faster charge transportation and extraction for PSCs. By employing the prepared Cu:NiOx films as HTLs for the PSCs, a high photocurrent density of 23.17 mA/cm2 and a high power conversion efficiency of 20.41% are obtained, which are superior to those with physical vapor deposited NiOx HTLs. Meanwhile, the PSC devices show a negligible hysteresis behavior and a long-term air-stability, even without any encapsulation. The results demonstrate that pulsed laser deposited Cu-doped NiOx film is a promising HTL for realizing high-performance and air-stable PSCs.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c15923?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c15923</a>.Experimental section, device characterization, and DFT calculations; cross-section SEM images and EDS spectra, carrier concentration and mobility, C-AFM characteristics, XPS spectra, UPS spectra, and RMS values of Cu:NiOx films; and statistical distribution of PSC devices (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c15923/suppl_file/am0c15923_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Thermal optimization of defected Cu2O photon-absorbing layer and the steady p-Cu2O/n-Si photovoltaic application

An all-sputtered photovoltaic ultraviolet photodetector based on co-doped CuCrO2 and Al-doped ZnO heterojunction

Preparation of CuO films at different sputtering powers and the effect of operating temperatures on the photovoltaic characteristics of p-CuO/n-Si heterojunction

Quasi‐Single Crystalline Cuprous Oxide Wafers via Stress‐Assisted Thermal Oxidation for Optoelectronic Devices

Interfacial Engineering of Cu 2 O Passivating Contact for Efficient Crystalline Silicon Solar Cells with an Al 2 O 3 Passivation Layer

Semitransparent Cu2O films based on CuO Back Layer for Photoelelctrochemical Water Splitting and Photovoltaic Applications

Novel interlayer boosting the performance of evaporated Cu2O hole‐selective contacts in Si solar cells

The Cu2O/CuO/SnO2 transparent pn junction film device towards photovoltaic enhancement with Cu2+ self-oxidation transition layer

Semitransparent Cu2O Films Based on CuO Back Layer for Photoelectrochemical Water Splitting and Photovoltaic Applications

High Efficiency Semiconductor‐Liquid Junction Solar Cells Based on Cu/Cu2O

Annealing temperature induced physical characteristics of CuO films grown by magnetron sputtering

Interface Connection Modulation by Heating Treatment for Photovoltaic Performance Enhancement on CuInS2 Quantum Dot Sensitized Solar Cells

CuO:Se composite films and its photovoltaic application

Effective carrier transport tuning of CuOx quantum dots hole interfacial layer for high-performance inverted perovskite solar cell

High-Efficiency and Stable Inverted Planar Perovskite Solar Cells with Pulsed Laser Deposited Cu-Doped NiO x Hole-Transport Layers

O, N co-doped CuCrO2 as efficient hole transport layer for high-performance ultraviolet photodetectors

Interfacial Study of Cu2o/Ga2o3/Azo/Tio2 Photocathode for Water Splitting Fabricated by Pulsed Laser Deposition

Optimizing the structure and optoelectronic properties of cuprite thin films via a plasma focus device as a solar cell absorber layer

Identification and Mitigation of a Critical Interfacial Instability in Perovskite Solar Cells Employing Copper Thiocyanate Hole‐Transporter

Photoelctrochemically Fabricated and Heated Cu2O/CuO Bilayers with Enhanced Photovoltaic Characteristics

Cu2O/CuO heterojunction formed by thermal oxidation and decorated with Pt co-catalyst as an efficient photocathode for photoelectrochemical water splitting