Abstract:Photoelectrochemical water splitting using semiconductor materials is one of the most promising methods for converting solar energy into chemical energy. Among the commonly used semiconductors, p-type CuBi2O4 is considered one of the most suitable photocathode materials and can allow a theoretical photocurrent density of about 20 mA center dot cm(-2) for photoelectrochemical water splitting. However, due to severe charge carrier recombination, the obtained photocurrent density is much lower than the theoretical value. Highly efficient photoelectrochemical performance relies on fast charge carrier separation and transport, and prompt reaction kinetics. In this study, we report the development of a polyoxometalate-modified CuBi2O4/Mg- CuBi2O4 homojunction photocathode to improve both the bulk and interfacial charge carrier transport in the photocathode. For the bulk of the photocathode, the built-in electric field originating from the CuBi2O4/Mg-CuBi2O4 homojunction promotes the migration of photo-excited electrons on the conduction band from pure CuBi2O4 to Mg-doped CuBi2O4. Additionally, the electric field facilitates the transfer of holes from the valence band of Mg-doped CuBi2O4 to pure CuBi2O4. This directional transfer of both photo-excited electrons and holes plays a significant role in promoting separation and suppressing the recombination of the charge carriers. On the surface of the photocathode, the reduced polyoxometalate co-catalyst Ag6[P2W18O62] (AgP2W18) was used as a proton sponge to accelerate surface reaction kinetics and suppress carrier recombination. These synergistic effects improved the photo-generated charge carrier transfer and reaction kinetics. As a result, the novel photocathode displayed excellent photoelectrochemical properties, and the photocurrent density was observed to be-0.64 mA center dot cm(-2) at 0.3 V vs. RHE, which is better than that of-0.39 mA center dot cm(-2) for a pure photocathode. Furthermore, the novel photocathode had an applied bias photon-to-current efficiency (ABPE) higher than 0.19% at 0.3 V vs. RHE. In contrast, the pure photocathode had an ABPE of similar to 0.12% under the same conditions. Additionally, when H2O2 was used as an electron scavenger, the photocurrent density was-3 mA center dot cm(-2) at 0.3 V vs. RHE, which is an improvement of approximately 1.5 times compared to the pure photocathode. Furthermore, the charge separation and charge injection efficiency of the novel photocathode were significantly improved compared with the pure photocathode. The experimental results conclusively indicate that the formation of the CuBi2O4/Mg-CuBi2O4 homojunction and AgP2W18 modification played a significant role in the improved performance of the CuBi2O4 photocathode. The performance of the novel photocathode was comparable with the results reported in previous studies, demonstrating its promising potential in real applications.

Cu2O/CuO heterojunction formed by thermal oxidation and decorated with Pt co-catalyst as an efficient photocathode for photoelectrochemical water splitting

CuBi2O4/CuO Heterojunction Coated with Electrodeposited ZnO Overlayer for Stable Solar Hydrogen Evolution

Highly Efficient 2D/3D Structured CuCo2S4/CdIn2S4 Composites with a P–n Heterojunction for Boosting Photocatalytic Hydrogen Evolution

Synthesis of a Cu2O/Carbon Film/NiCoB‐Grpahene Oxide Heterostructure As Photocathode for Photoelectrochemical Water Splitting

Si-doped Cu2O/SiOx composites for efficient photoelectrochemical water reduction

Design and In Situ Growth of Cu 2 O‐Blended Heterojunction Directed by Energy‐Band Engineering: Toward High Photoelectrochemical Performance

Co-optimization of CuBi2O4 photocathode by heterojunction and hole-selective layer for efficient photoelectrochemical water splitting

Cu ions intercalated GO/Cu 2 O photocathode-enabled promotion on charge separation and transfer for efficient photoelectrochemical water splitting

Surface densification strategy assisted efficient Cu2O heterojunction photocathode for solar water splitting

Enhancement of Solar-to-hydrogen Conversion Efficiency in Water Splitting by Optimizing Morphology of Cu2O Nanostructure and Surface Modification

ZnO photoelectrode simultaneously modified with Cu2O and Co-Pi based on broader light absorption and efficiently photogenerated carrier separation

Electrodeposition of Copper Oxides as Cost-Effective Heterojunction Photoelectrode Materials for Solar Water Splitting

Integration of a Cu2O/ZnO heterojunction and Ag@SiO2 into a photoanode for enhanced solar water oxidation

In situ synthesized In2O3/CuBi2O4 heterojunction photocathodes for efficient photoelectrochemical water splitting

Semitransparent Cu2O films based on CuO Back Layer for Photoelelctrochemical Water Splitting and Photovoltaic Applications

Improvement of the Photoelectrochemical Stability of Cu2O Photocathode by PhCCCu Grafting

Cu2O as an emerging photocathode for solar water splitting - A status review

Cu2O Photocathodes for Unassisted Solar Water-Splitting Devices Enabled by Noble-Metal Cocatalysts Simultaneously As Hydrogen Evolution Catalysts and Protection Layers

Investigation of CuO/ITO Photoelectrode Fabricated by PVD for Efficient Photoelectrochemical Water Splitting and Hydrogen Evolution

CuO/CuBi2O4 bilayered heterojunction as an efficient photocathode for photoelectrochemical hydrogen evolution reaction

Improved Photoelectrochemical Performance by Polyoxometalate-Modified CuBi2O4/Mg-CuBi2O4 Homojunction Photocathode