Abstract:Objective: The aim of this study was to examine the shear bond strength (SBS) of ceromer and nanohybrid composite to direct laser sintered (DLS) Cr-Co and Ni-Cr-based metal infrastructures treated with erbium-doped yttrium aluminum garnet (Er:YAG), neodymium-doped yttrium aluminum garnet (Nd:YAG), and potassium titanyl phosphate (KTP) laser modalities in in vitro settings. Methods: Experimental specimens had four sets (n = 32) including two DLS infrastructures with ceromer and nanohybrid composite superstructures and two Ni-Cr-based infrastructures with ceromer and nanohybrid composite superstructures. Of each infrastructure set, the specimens randomized into four treatment modalities (n = 8): no treatment (controls) and Er:YAG, Nd:YAG, and KTP lasers. The infrastructures were prepared in the final dimensions of 7 × 3 mm. Ceromer and nanohybrid composite was applied to the infrastructures after their surface treatments according to randomization. The SBS of specimens was measured to test the efficacy of surface treatments. Representative scanning electron microscopy (SEM) images after laser treatments were obtained. Results: Overall, in current experimental settings, Nd:YAG, KTP, and Er:YAG lasers, in order of efficacy, are effective to improve the bonding of ceromer and nanohybrid composite to the DLS and Ni-Cr-based infrastructures (p < 0.05). Nd:YAG laser is more effective in the DLS/ceromer infrastructures (p < 0.05). KTP laser, as second more effective preparation, is more effective in the DLS/ceromer infrastructures (p < 0.05). SEM findings presented moderate accordance with these findings. Conclusions: The results of this study supported the bonding of ceromer and nanohybrid composite superstructures to the DLS and Ni-Cr-based infrastructures suggesting that laser modalities, in order of success, Nd:YAG, KTP, and Er:YAG, are effective to increase bonding of these structures.

Evaluation of the critical SERR in the presence of heterogeneous interfaces in bonded joints: application to parallel defects in DCB titanium alloy laser-treated specimens

Evaluation of the cracked lap shear test for mixed-mode fracture toughness estimation of adhesive joints

Nonlinear Fracture Analysis of Delamination Crack Jumps in Laminated Composites

An elastic-plastic cohesive zone model for metal-ceramic interfaces at finite deformations

Quantitative In-Situ Study of Strength-Governed Interfacial Failure Between H-Bn and Polymer-Derived Ceramic

Porosity estimation of a micro-cracked adhesive interface by μCT scanning: Comparison between experimentally measured effective stiffnesses and those predicted by an imperfect interface model

Multi-scale analysis of the adhesive bonding behavior of laser surface-treated carbon fiber reinforced polymer composite structures

Prediction of effective cohesive parameters for mode I failure behavior of LPBF Ti-6Al-4 V/CFRTP interface using meso -scale modelling

Effect of laser pre-treatment on adhesive joint performance and evaluation of interfacial strain distribution using mechanoluminescence

Characterization of Mode-I fracture of hybrid material interface bonds by contoured DCB specimens

Mixed-Mode Fracture Of Hybrid Material Bonded Interfaces Under Four-Point Bending

On the Fracture Resistance of Adhesively Jointing Structures

Experimental and theoretical studies on laser treatment strategies for improving shear bonding strength of structural adhesive joints with cast aluminum

Increasing strength and fracture toughness of AA7075-T6 adhesively-bonded joints with laser ablation

In situ SEM study on tensile fractured behavior of Al/steel laser welding-brazing interface

Enhancing Interlaminar Bonding Quality Estimation in Laser-Assisted Fiber Placement of CF/PEKK Composites: A Correction Factor Approach for Improved Prediction of Intimate Contact

On enhancement of fracture resistance of adhesive joints by surface micropatterning using a femtosecond laser

Shear Bond Strength of Composite and Ceromer Superstructures to Direct Laser Sintered and Ni-Cr-Based Infrastructures Treated with KTP, Nd:YAG, and Er:YAG Lasers: An Experimental Study

Synergistic Interface Effects on Mechanical Properties: in Situ Study on Fracture Behaviors of Al Matrix Composite Joint

Influence of Defects During the Tensile Deformation of Cu–Al Joint Interfaces at the Nano Scale

Investigation on the Stable and Stick-Slip Crack Propagation Behaviors in Double Cantilever Beam Test