Abstract:Mechanism analysis, process optimisation and validation of laser surface treatment. Adhesive bonding has gradually replaced mechanical connections as the primary method for composite material bonding, with surface quality being the key factor determining the effectiveness of composite material adhesion. Laser surface treatment, known for its green and precise characteristics, has garnered widespread attention from both academia and industry. However, the process parameters of laser surface treatment are complex, efficiency is low, and the mechanism remains unclear. This paper, based on the response surface methodology (RSM), investigates the influence of laser secondary parameters on the resin removal rate of carbon fiber reinforced polymer/plastic (CFRP) surfaces and the impact of defocusing on surface treatment efficiency. The results indicate that when the total laser energy density (Et) is 69 J/cm2, the overlap ratio in the warp direction (OLs) is 76%, and the overlap ratio in the weft direction (OLh) is 85%, the surface tensile shear strength increases by 90.59% and 27.77% compared to the original surface and polished surface, respectively. When the defocus distance is +8 mm, the efficiency of laser surface treatment is 2.25 times that of non‐defocus, with minimal impact on mechanical performance. The surface treatment mechanism, with changes in Et, primarily involves the pure thermal decomposition of the resin matrix in an oxygen‐free environment, oxidative decomposition, and the synergistic action of the decomposition products' oxidation. Through the coupled optimization of laser process parameters, this work enhances the efficiency and effectiveness of composite material adhesive surface treatment, promoting the engineering application of laser technology. Highlights By establishing a response surface model, the study elucidated the impact patterns of laser secondary parameters (overlap rates in the warp and weft directions, total energy density) on the resin removal rate of CFRP surfaces. Based on the laser surface treatment phenomena at different total energy densities, the study analyzed and revealed the mechanism of near‐infrared (1064 nm) laser resin removal from CFRP surfaces. By increasing the spot size through defocusing, the efficiency of laser surface treatment was enhanced, and the impact on the interfacial properties of CFRP after defocused treatment was validated.

Enhancing Interlaminar Bonding Quality Estimation in Laser-Assisted Fiber Placement of CF/PEKK Composites: A Correction Factor Approach for Improved Prediction of Intimate Contact

Influence of Process Parameters on the Interlaminar Shear Strength of CF/PEEK Composites In-Situ Consolidated by Laser-Assisted Automated Fiber Placement

Deformation and Fracture Mechanisms of Automated Fiber Placement Pre-Preg Laminates under Out-of-plane Tensile Loading

Multi-scale analysis of the adhesive bonding behavior of laser surface-treated carbon fiber reinforced polymer composite structures

Mechanism and Behavior of Laser Irradiation on Carbon Fiber Reinforced Polyetheretherketone (CF/PEEK) During the Laser-Assisted In-Situ Consolidation Additive Manufacturing Process

Modeling on the Effect of Automated Fiber Placement Induced Gaps in Curved Composite Laminates

Interlayer bonding improvement of PEEK and CF-PEEK composites with laser-assisted fused deposition modeling

Strength and failure mechanism of single-lap magnesium-basalt fiber metal laminate adhesively bonded joints: Experimental and numerical assessments

Investigation of analysis and improvement of the assessment of bonding performance for thermoplastic composites

Investigation of laser-patterned biomimetic microstructures on CFRP and AA5052 surfaces to enhance their single-lap bonding strength

Experimental and numerical study on the tensile failure behavior of toughened-interlayer composite laminates with automated fiber placement (AFP) induced gap and overlap defects

Study on Mode I interlaminar fracture behavior of automated fiber placement in situ consolidation thermoplastic composite considering the influence of roller compaction pressure

Effects of surface treatments and bonding types on the interfacial behavior of fiber metal laminate based on magnesium alloy

Experimental Study on the Influence of Optimised Automated Fibre Placement Processing Parameters on the Impact Response and Residual Flexural Strength of AS4/APC-2 Laminates

The Effects of Combined Treatments of Laser Engraving, Plasma Spraying and Resin Pre-Coating on Improving the Bonding Strength of Titanium Alloy and Carbon Fiber-Reinforced Polymer

Material and adhesive effect in adhesively-bonded composite stepped-lap joints

PHASE FIELD BASED COHESIVE ZONE FRACTURE APPROACH TO MODEL ANISOTROPIC EFFECT AND INTERFACE FRACTURE IN FIBER REINFORCED POLYMER COMPOSITES

Experimental study of the influence of adhesive reinforcement in lap joints for composite structures subjected to mechanical loads

Process optimization and performance verification of CFRP laser surface modification

Optimization of microstructural morphology via laser processing to enhance the bond strength of Al-CFRP

The Effect of Resin Interleafing on the Wedge Peel Strength of CF/PEEK Manufactured by Laser-Assisted In Situ Consolidation