Abstract:<p>The laser ablation treatment has been validated to be an effective surface treatment method in improving adhesive bonding performance for metal or composite materials. This study was further conducted to investigate the effect of laser spot overlap ratio on surface characteristics and resultant adhesive bonding strength for AA6022-T4 Al alloy. The laser spot overlap ratio was changed by varying the laser processing speed and line spacing between laser scanning lines. Surface characteristics analyses show that the laser ablation treatment at higher overlap ratio produces rougher surface morphology and thicker aluminum oxide layer on substrate surface, which are considered to be more favorable for adhesive bonding strength. Lap-shear strength results show that the laser ablation treatment at overlap ratio of -49 % (corresponding with separated laser spots) improves the joint strength by 6.8 % and 17.1 % before and after water soak exposure compared to as-received condition. Meanwhile, the desired cohesive fracture mode is also achieved which indicates that the joint strength reaches to the saturated value depending on mechanical performance of adhesive. This explains that the continuous increase of laser spot overlap ratio from -49 % to 63 % exhibits negligible improvement on joint strength. Nevertheless, although inducing a higher degree of surface physicochemical modifications on Al substrates, the laser ablation treatment with an overlap ratio beyond 63 % decreases the joint strength. Detailed studies of SEM micrographs verified that the decreased joint strength is attributed to insufficient wetting of adhesive on the rough surfaces of laser-treated substrates resulting in entrapment of air between substrate and adhesive layer, which forms micropores defects in the adhesive layer and consequently weakens the adhesive-bonding joints. In addition, the improved corrosion resistance of adhesive-bonded Al joints by laser ablation treatment is attributed to the barrier effect of laser-produced rough surface morphology to water diffusion along bonding interface.</p>

On enhancement of fracture resistance of adhesive joints by surface micropatterning using a femtosecond laser

Effect of laser pre-treatment on adhesive joint performance and evaluation of interfacial strain distribution using mechanoluminescence

Increasing strength and fracture toughness of AA7075-T6 adhesively-bonded joints with laser ablation

Nanosecond laser ablation for improving the strength of CFRTP and aluminum alloy adhesively bonded joints

Experimental and theoretical studies on laser treatment strategies for improving shear bonding strength of structural adhesive joints with cast aluminum

Adhesion Enhancement of PEEK/6161-T6 FLJ Joints Via Laser Surface Modification

Optimization of microstructural morphology via laser processing to enhance the bond strength of Al-CFRP

Influence of the different surface treatments on fracture property of CFRP adhesive joint

Effect of laser spot overlap ratio on surface characteristics and adhesive bonding strength of an Al alloy processed by nanosecond pulsed laser

Experimental and Theoretical Investigation of Laser Pretreatment on Strengthening the Heterojunction Between Carbon Fiber Reinforced Plastic and Aluminum Alloy.

Investigation of laser-patterned biomimetic microstructures on CFRP and AA5052 surfaces to enhance their single-lap bonding strength

Comparison of the effects of femtosecond and nanosecond laser tailoring on the bonding performance of the heterojunction between PEEK/CFRP and Al–Li alloy

Influence of Laser Process Parameters on the Characteristic of 30crmnsia Steel Substrate and Adhesively Bonded Joints

Effect of IR ‐laser treatment parameters on surface structure, roughness, wettability and bonding properties of fused deposition modeling‐printed PEEK / CF

Mechanism of laser-inducing hierarchical surface structures improving bonding strength of metal-plastic hybrids

Analysis of the Effect of Surface Preparation of Aluminum Alloy Sheets on the Load-Bearing Capacity and Failure Energy of an Epoxy-Bonded Adhesive Joint

Crack propagation in adhesive bonded 3D printed polyamide: Surface versus bulk patterning of the adherends

Effect of Mechanical Pretreatments on Damage Mechanisms and Fracture Toughness in CFRP/Epoxy Joints

Effect of Groove Configuration on Mechanical Properties and Fracture Behavior of 6061 Al Alloy and CFRTP Laser Joint

Insights into the micromechanical response of adhesive joint with stochastic surface micro-roughness

Effect of laser surface texture on the adhesion performance of CFRP/Mg laminates