Abstract:Mechanism analysis, process optimisation and validation of laser surface treatment. Adhesive bonding has gradually replaced mechanical connections as the primary method for composite material bonding, with surface quality being the key factor determining the effectiveness of composite material adhesion. Laser surface treatment, known for its green and precise characteristics, has garnered widespread attention from both academia and industry. However, the process parameters of laser surface treatment are complex, efficiency is low, and the mechanism remains unclear. This paper, based on the response surface methodology (RSM), investigates the influence of laser secondary parameters on the resin removal rate of carbon fiber reinforced polymer/plastic (CFRP) surfaces and the impact of defocusing on surface treatment efficiency. The results indicate that when the total laser energy density (Et) is 69 J/cm2, the overlap ratio in the warp direction (OLs) is 76%, and the overlap ratio in the weft direction (OLh) is 85%, the surface tensile shear strength increases by 90.59% and 27.77% compared to the original surface and polished surface, respectively. When the defocus distance is +8 mm, the efficiency of laser surface treatment is 2.25 times that of non‐defocus, with minimal impact on mechanical performance. The surface treatment mechanism, with changes in Et, primarily involves the pure thermal decomposition of the resin matrix in an oxygen‐free environment, oxidative decomposition, and the synergistic action of the decomposition products' oxidation. Through the coupled optimization of laser process parameters, this work enhances the efficiency and effectiveness of composite material adhesive surface treatment, promoting the engineering application of laser technology. Highlights By establishing a response surface model, the study elucidated the impact patterns of laser secondary parameters (overlap rates in the warp and weft directions, total energy density) on the resin removal rate of CFRP surfaces. Based on the laser surface treatment phenomena at different total energy densities, the study analyzed and revealed the mechanism of near‐infrared (1064 nm) laser resin removal from CFRP surfaces. By increasing the spot size through defocusing, the efficiency of laser surface treatment was enhanced, and the impact on the interfacial properties of CFRP after defocused treatment was validated.

Effect of laser surface texture on the adhesion performance of CFRP/Mg laminates

Laser Cleaning Treatment and its Influence on the Surface Microstructure of CFRP Composite Material

Mechanism and Behavior of Laser Irradiation on Carbon Fiber Reinforced Polyetheretherketone (CF/PEEK) During the Laser-Assisted In-Situ Consolidation Additive Manufacturing Process

Process optimization and performance verification of CFRP laser surface modification

Influence of the different surface treatments on fracture property of CFRP adhesive joint

Influence of Process Parameters on the Interlaminar Shear Strength of CF/PEEK Composites In-Situ Consolidated by Laser-Assisted Automated Fiber Placement

Optimization of microstructural morphology via laser processing to enhance the bond strength of Al-CFRP

Effect of laser pre-treatment on adhesive joint performance and evaluation of interfacial strain distribution using mechanoluminescence

Effect of laser texturing on mechanical strength and microstructural properties of hot-pressing joining of carbon fiber reinforced plastic to Ti6Al4V

Effect of the laser texturing width on hot-pressing joining of AZ31B and CFRTP

Experimental and Theoretical Investigation of Laser Pretreatment on Strengthening the Heterojunction Between Carbon Fiber Reinforced Plastic and Aluminum Alloy.

Surface Integrity of Water Jet Guided Laser Machining of CFRP

Multi-scale analysis of the adhesive bonding behavior of laser surface-treated carbon fiber reinforced polymer composite structures

Effect of Mechanical Pretreatments on Damage Mechanisms and Fracture Toughness in CFRP/Epoxy Joints

Effects of laser hybrid interfacial pretreatment on enhancing the carbon fiber reinforced thermosetting composites and TC4 alloy heterogeneous joint

Influence of laser texturing on the properties of fusion joints between aluminum alloys and carbon fiber reinforced thermoplastic composites

Enhancing Bond Strength Between Carbon Fiber Reinforced Thermoplastic and Aluminum Alloys Through Laser Surface Treatment

Laser surface treatment to enhance the adhesive bonding between steel and CFRP: Effect of laser spot overlapping and pulse fluence

Laser Melting and Surface Texture Technology: Effect on Friction Properties

The Influence of Laser Process Parameters on the Adhesion Strength between Electroless Copper and Carbon Fiber Composites Determined Using Response Surface Methodology

EFFECT OF THE SURFACE TEXTURE ON LASER JOINING OF A CARBON FIBER-REINFORCED THERMOSETTING PLASTIC AND STAINLESS STEEL