Abstract:It is essential to study the tensile fracture mechanism of additively manufactured materials and develop the effective process treatment techniques to improve their fracture resistance. In this paper, the effects of different treatment processes on the microstructure and tensile fracture properties of TC17 titanium alloy melted by laser selective zone melting were investigated. The static tensile fracture morphological characteristics were observed by combining SEM and EDS. The metallographic microstructure after chemical corrosion was observed optically. And the tensile fracture morphology of the three states of TC17 titanium alloy samples at room temperature conditions was investigated. The results show that the metallographic matrix microstructure of TC17 titanium alloy after HT, HIP and HIP-HT treatments was a bimodal structure with α+β phases, i.e., β phase was in the form of a net basket, and α phase was in the form of a coarse bar. The grain sizes of the samples treated by different processes were different, but the difference in grain size of the HT-treated tissues was small, and the difference in grain size of the HIP-HT-treated tissues was large. And the coarse α-phase segregation could be seen at the edge of the samples. The 3D-printed materials had complex changes in anisotropic properties affected by the printing structure and tissue. The printed tissues were brittle and had high internal stresses. These problems were partly improved at high temperatures, but they still existed. The HIP-HT-treated materials had a large α+β-phase bimodal structure. The HT-treated material had coarse grains and precipitation phases, poor room temperature plasticity, and improved high temperature plasticity. After HT treatment, the original printing microstructure changed, the strength and plasticity were significantly improved, but the macroscopic printing structure still had a slight influence on the fracture morphology. When HIP treatment temperature was higher, the influence of macroscopic printing structure basically disappeared, but the grain and microstructure grew up, and the strength and plasticity were slightly lower than that of the HT treatment. HIP process basically eliminated the unfused defects of the three-dimensional morphology, and the local weak bonding zone formed.

In-situ investigation on tensile deformation and fracture behaviors of inhomogeneous microstructure during laser repair of Ti-6Al-4 V titanium alloy

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

In Situ Electron Backscatter Diffraction Study of Deformation Inhomogeneity under Uniaxial Tension of Laser Melting Deposited TA15 Alloy

Effect of Scanning Strategy on Microstructure Evolution and Stress Control in Laser Cladding Repair of Ti6Al4V Alloy

In-Situ SEM Study on Deformation and Failure Mechanism of TC4 Titanium Alloy by Laser Additive Manufacturing

In Situ Tensile Observation of the Effect of Annealing on Fracture Behavior of Laser Additive Manufactured Titanium Alloy

Micro-deformation behavior of laser melting deposited multi-gradient TC4/TC11 alloy under tension-tension cyclic loading

An investigation of ductile fracture behavior of Ti6Al4V alloy fabricated by selective laser melting

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

In-situ investigation on the anisotropic behavior of the additively manufactured dual-phase Ti-6Al-4V alloy

Tensile failure analysis of laser stake-welded T-joints: X-ray tomography based conformal finite element and fractal theoretical approaches

Effects of different treatment processes on microstructure and tensile fracture behaviour of selected laser melting TC17 titanium alloy

Failure Behavior of Laser Metal Deposited Additive Manufacturing Ti-6Al-4V: Effects of Stress State and Initial Defects

Revealing Tensile Behaviors and Fracture Mechanism of Ti–6Al–4V Titanium Alloy Electron-Beam-welded Joints Using Microstructure Evolution and in Situ Tension Observation

Microstructural Strengthening and Plastic Degradation of Ti–6Al–4V Induced by Laser Ablation

Study on the Tensile and Shear Behaviors of Selective Laser Melting Manufactured Ti6Al4V

In-Situ Study on Tensile Deformation and Fracture Mechanisms of Metastable β Titanium Alloy with Equiaxed Microstructure

Microstructure and High-Temperature Tensile Properties of Ti3Al Alloys Laser Welding Joint

In situ tensile test of selective laser melted Ti-6.5Al-2Zr-1Mo-1V alloy at different stages of martensite decomposition

Microstructures and mechanical properties of Ti6Al4V alloy repaired by the technology of point-mode forging and laser repairing