Abstract:This study compares the microstructure and tensile properties of Ti6Al4V components fabricated by laser direct metal deposition (LDMD) additive manufacturing (AM) in the transverse and longitudinal directions. The results show anisotropic tensile properties with the transverse direction having high tensile and fracture strengths and the longitudinal direction having a high elongation and reduction of cross section. The anisotropic mechanical properties are attributed to the anisotropic microstructural distribution. The transverse tensile specimen is composed of short columnar prior-β grains which grow perpendicular to the tensile direction, and have a lamellar structure. Along the β grain boundary, αGB and large α colonies were identified. However, the longitudinal specimen shows that the long β structure is parallel to the tensile axis and that the microstructure is composed of basket-woven α phases with shorter α plates and smaller colony sizes compared with those in the transverse specimen. The fracture mechanism induced by the anisotropic microstructure along the transverse and longitudinal directions was compared by examining the fracture process in real-time using uniaxial in-situ scanning electron microscopy (SEM) tensile testing. The results show that shear fracture, which is caused by the vertical β grain boundaries and large α colonies with long α plates, occurs in the transverse specimen. The shear mode is the main reason behind the enhanced tensile strength and fracture strength due to the high resistance to microcrack propagation. However, in the longitudinal specimens, symmetric necking behavior due to the fine α grains resulted in uniform deformation of the grains on both sides of the grain boundaries, inducing greater elongation.

In-situ investigation on the anisotropic behavior of the additively manufactured dual-phase Ti-6Al-4V alloy

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

An investigation of ductile fracture behavior of Ti6Al4V alloy fabricated by selective laser melting

Microstructure and Anisotropic Mechanical Properties of Selective Laser Melted Ti6Al4V Alloy under Different Scanning Strategies

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Discovering the role of the defect morphology and microstructure on the deformation behavior of additive manufactured Ti–6Al–4V

Influence of Modified Microstructures and Characterized Defects on Tensile Properties and Anisotropy of Selective Laser Melting-Produced Ti6Al4V Alloys

In Situ Tensile Observation of the Effect of Annealing on Fracture Behavior of Laser Additive Manufactured Titanium Alloy

Multiple Α Sub-Variants and Anisotropic Mechanical Properties of an Additively-Manufactured Ti-6Al-4V Alloy

Phase transformation mechanisms, microstructural characteristics and mechanical performances of an additively manufactured Ti-6Al-4V alloy under dual-stage heat treatment

Tensile Behavior of Ti-6Al-4V Alloy Fabricated by Selective Laser Melting: Effects of Microstructures and As-Built Surface Quality

In-situ SEM Observations of Tensile Deformation Behavior of Ti555211 Alloy with Dual Structure

On Defect Evolution in EBM Additively Manufactured Ti-6Al-4V via In Situ Investigations

Deformations of Ti-6Al-4V additive-manufacturing-induced isotropic and anisotropic columnar structures: Insitu measurements and underlying mechanisms

In-Situ SEM Study on Deformation and Failure Mechanism of TC4 Titanium Alloy by Laser Additive Manufacturing

Study on the Tensile and Shear Behaviors of Selective Laser Melting Manufactured Ti6Al4V

Failure Mechanism and Mode of Ti-6Al-4V Alloy under Uniaxial Tensile Loading: Experiments and Micromechanical Modeling

Mechanical Behavior Assessment of Ti-6Al-4V ELI Alloy Produced by Laser Powder Bed Fusion

Experimental and Crystal Plasticity Finite Element Investigations of Plastic Anisotropy in Additively Manufactured Ti6Al4V Alloy