Abstract:Elasto-plastic numerical analyses have been carried out for bonded dissimilar materials with different hardening properties, by using the boundary element method (BEM) and the finite element method (FEM). From the stress distribution near the interface edge, the elasto-plastic singular behavior has been investigated. It is found that there will be a meaningful region within which the elasto-plastic singular stress field becomes dominant under the large scale yielding condition. Therefore the fracture shall be evaluated by the elasto-plastic interfacial mechanics for such a case. The singularities determined numerically agree well with the theoretical results. It is also found that both the size of the yield zone and the stress distribution near the edge are dependent of the material combination. However, in the side of the material with smaller hardening exponent (the “harder” side), the theoretical singular stress field is not valid. Moreover, if the difference between two hardening exponents of the composed materials is very small, the displacement-matching method is no longer applicable. It is also found that the properties of the material with smaller hardening exponent mainly influence the angular stress distribution around the interface edge, but have very few effects on the singular stress order. It is also verified that the theoretical elastic solution of the singular stress field remains useful under the small scale yielding condition. Introduction Structures composed of bonded dissimilar materials have a wide application in engineering. To evaluate their strengths or reliabilities, the linear interfacial mechanics has been developed in the last decade [1]. However, for the cases such as ceramic/metal joints in which the yield strength of one composed material is relatively low, the elasto-plastic stress singular behavior [2-4] near the interface edge may have a strong effect on the strength. The evaluation approach based on the elasto-plastic interfacial mechanics is necessary. The authors [5] have theoretically deduced the elasto-plastic singular stress field near the interface edge of bonded linear hardening materials. It is found that the elasto-plastic stress singular behavior depends on not only the hardening coefficients, but also on the elastic properties. The elasto-plastic singular stress in this case can be determined by the two generalized Dundurs’ parameter and the geometry of the interface edge. The authors [6] have also proposed a method to determine the elasto-plastic stress singular order and the distribution near the interface edge of bonded dissimilar power-law hardening materials, based on the displacementmatching method [7,8] and two path-independent integrals. It is found that when the interface edge is degenerated to an interface crack, the results obtained by this method agree with that for an interface crack [7,8]. In this study, the elasto-plastic boundary element method (BEM) and finite element method (FEM) analyses have been carried out to investigate the elasto-plastic singular behaviors of bonded linear and power-law hardening materials, respectively. Based on the comparison of the numerical and the theoretical results, the validity and the applicable range of the theoretical solutions have been clarified. Interface edge of Bonded Linear Hardening Materials Theoretical Results Introducing the generalized Dundurs’ parameters as [5]

An elastic-plastic cohesive zone model for metal-ceramic interfaces at finite deformations

Cohesive zone modeling for viscoplastic behavior at finite deformations

Irreversible Deformation of Metal Matrix Composites: A Study Via the Mechanism-Based Cohesive Zone Model

An Incremental Elastic-Plastic Cohesive Constitutive Model with Considering Damage

A Phase-Field-cohesive-zone Framework to Simulate Multiple Failure Mechanisms of Elastoplastic Fiber-Reinforced Composites

A modified phase-field model for cohesive interface failure in quasi-brittle solids

Finite Element Analysis of Interfacial Debonding Damage in Fiber-Reinforced Ceramic Matrix Composites

A minimalistic approach to simulate multiple failure mechanisms of metal matrix fiber-reinforced composites by the phase field and cohesive zone models

Recent Advances in Cohesive Zone Modelling of Fracture

An interface-width-insensitive cohesive phase-field model for fracture evolution in heterogeneous materials

A cohesive zone model for the elevated temperature interfacial debonding and frictional sliding behavior

Failure Characterization of Solid Structures Based on an Equivalence of Cohesive Zone Model

Interfacial Shear Stress Transfer Between Elastoplastic Fiber and Elastic Matrix

A cohesive zone model incorporating a Coulomb friction law for fiber-reinforced composites

Modeling Microfracture Evolution in Heterogeneous Composites: A Coupled Cohesive Phase-Field Model

Phase field modeling of dynamic fracture in elastoplastic composites with interfacial debonding

Elasto-Plastic Singular Behavior at an Interface Edge

A novel phase‐field based cohesive zone model for modeling interfacial failure in composites

The Effect of Imperfect Interface on the Dynamic Behavior of Ceramic Particles Reinforced Metal Matrix Composites

A Multiscale Cohesive Zone Model for Rate-Dependent Fracture of Interfaces

Molecular dynamics simulations of interface structure and deformation mechanisms in metal/ceramic composites under tension