Abstract:Crystallographic textures and their effect on the mechanical anisotropy of a hot-rolled biomedical Co-Cr-Mo alloy were investigated. The hot-rolled Co-28Cr-6Mo-0.13N (mass%) alloy examined here exhibited a monotonic strength increment following hot-rolling reduction, eventually reaching a 0.2% proof stress of 1400 MPa while maintaining acceptable ductility (>10%). The dominant hot-rolling texture was a brass-type component, which is characterized by the alloy's peculiarly low stacking fault energy (SFE) even at hot rolling temperatures, although the minor peaks of the near copper component were also identified. However, because of the onset of dynamic recrystallization (DRX) during the hot rolling process, the texture intensity was relatively weak even after 90% hot rolling, although the grain refinement originating from the DRX was not significant (the "less active DRX" condition increased the strain accumulation during the process, resulting in high-strength samples). The weakened texture development resulted in negligible in-plane anisotropy for the hot-rolled specimen strength, when the specimens were tensile strained in the rolling direction (RD) and transverse direction (TD). The elongation-to-failure, however, exhibited a difference with respect to the tensile loading axis. It is suggested that the ductility anisotropy is closely related to a strain-induced γ (fcc) → ε (hcp) martensitic transformation during tensile loading, resulting in a difference in the proportion of quasi-cleavage fracture surfaces. The obtained results will be helpful in the development of high-strength Co-Cr-Mo alloy plates and sheets, and have implications regarding plastic deformation and texture evolution during the hot rolling of non-conventional metallic materials with low SFE at elevated temperatures, where planar dislocation slips of Shockley partial dislocations and thermally activated process interplay.

Effect of stress-relief annealing on rolled texture of nickel-based alloys

Effect of cross cold rolling and annealing on microstructure and texture in pure nickel

Effect of different deformation and annealing procedures on non-magnetic textured Cu60Ni40 alloy substrates

Systematic investigation of the texture evolution of Cu-Ni alloys with different strains

Development of the Cube Texture at Low Annealing Temperatures in Highly Rolled Pure Nickel

Development and Stability During High Temperature Annealing of the Cube Texture in Rolled Ni Substrate Materials

Microstructure and Texture Evolution of Cu-Ni-P Alloy after Cold Rolling and Annealing

Effect of Annealing Temperature on Cube Texture Formation in Ni7W/Ni12W/Ni7W Compound Substrate

Evolution of Microstructure and Texture During Recovery and Recrystallization in Heavily Rolled Aluminum

Texture evolution and mechanical anisotropy of biomedical hot-rolled Co-Cr-Mo alloy

Microstructure and Texture Evolution of Cold Rolled 1070 Al Alloy During the Subsequent Annealing Treatment

RELEVANCE OF COLD-ROLLING TECHNOLOGY FOR THE TEXTURE AND ANISOTROPY OF EN AW-8011A ALUMINUM ALLOYS

Effects of Strain on Recrystallization of Nickel Metals and Nanometals Produced by Heavy Cold Rolling

Recovery and Recrystallization as a Function of Deformed Microstructure Orientation in Coarse Grained Cold-Rolled Ni

Analysis of the Ni-5%at.W Alloy Substrate Texture Evolution at Different Strain Levels Using the EBSD Technique

Influence of Intermediate Annealing on the Microstructure and Texture of Ni-9.3at%W Substrates

Effect of Reduction on High Temperature Annealing of Cold-Rolled Ni

Evolutions of Microstructure and Crystallographic Texture in an Fe-1.2 wt.% Si Alloy After (A)Symmetric Warm Rolling and Annealing

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Deformation And Annealing Textures Of Extruded And Cold Rolled Pure Ni Single Crystals Of Cube Orientation

Reduction per pass effect on texture traits and mechanical anisotropy of Mg–Al–Zn–Mn–Ca alloy subjected to unidirectional and cross rolling