Abstract:In this paper, the texture evolution of the Ni-5%W alloy baseband with different strain variables (εvM = 3.9, 4.9, and 5.1) during rolling and annealing was studied using the electron back scattering diffraction (EBSD) technique. The results indicate that after high-temperature annealing at 1150 °C, all three strain levels of the alloy substrates can achieve a strong cubic texture, with a content exceeding 99% (<10°). However, the texture evolution trajectory is significantly influenced by the strain level. When the content of cubic texture in the alloy substrates under strain levels of 3.9 and 5.1 is the same, significant temperature differences exist. Additionally, the different strain levels result in varying nucleation rates and growth rates of cubic texture in the Ni-5%W alloy substrates. The study reveals that in the alloy substrates under strain levels of 3.9 and 4.9, recrystallized cubic grain nuclei grow within a layered structure, resulting in larger grain sizes and lower nucleation rates. In contrast, in the alloy substrates under a strain level of 5.1, recrystallized cubic grain nuclei form from small equiaxed grains, leading to higher nucleation rates but smaller grain sizes, competing with random orientations. In the later stages of nucleation, recrystallized grains in the alloy substrates under a strain level of 5.1 exhibit a significant size advantage, rapidly growing by engulfing randomly oriented grains. Compared to the alloy substrates with lower strain levels, the recrystallized cubic grains in the alloy substrates under a strain level of 5.1 have higher nucleation rates and faster growth rates.

Effect of Annealing Temperature on Cube Texture Formation in Ni7W/Ni12W/Ni7W Compound Substrate

Development and Stability During High Temperature Annealing of the Cube Texture in Rolled Ni Substrate Materials

Effect of different deformation and annealing procedures on non-magnetic textured Cu60Ni40 alloy substrates

Preparation and Evaluation of Cube Texture Ni Substrate for Ybco-Coated Superconductor

Strong Cube Texture Formation of Ni5W/Ni9.3W/Ni5W Composite Thin Substrates for YBCO-coated Conductors

Influence of Intermediate Annealing on the Microstructure and Texture of Ni-9.3at%W Substrates

Strong Cube Texture Formation in Heavily Cold-Rolled Ni8W/Ni12W/Ni8W Composite Alloy Substrates Used in YBCO Coated Conductors

Development of the Cube Texture at Low Annealing Temperatures in Highly Rolled Pure Nickel

Fabrication of Textured Ni–9.3at.%W Substrate by Electropulsing Intermediate Annealing Method

Strong Cube Texture of Super-High Tungsten Ni–W Alloy Substrates Used in REBCO Coated Conductors

Cube Texture Development in Pure Ni during Annealing in a High Strength Magnetic Field

Preparation of cube texturing Ni plate by rolling and recrystallization

Evolution of Microstructure, Texture and Topography During Cold Rolling and Recrystallization of Ni–5at.%W Alloy Substrate for Coated Conductors

Effect of Reduction on High Temperature Annealing of Cold-Rolled Ni

Effect of stress-relief annealing on rolled texture of nickel-based alloys

Ion-Beam Bombardment Induced Texture in Nickel Substrates for Coated High-T-C Superconductors

Deformation And Annealing Textures Of Extruded And Cold Rolled Pure Ni Single Crystals Of Cube Orientation

Effect of cross cold rolling and annealing on microstructure and texture in pure nickel

Analysis of the Ni-5%at.W Alloy Substrate Texture Evolution at Different Strain Levels Using the EBSD Technique

Microstructural peculiarities and textural characteristics of Ni–W sheet alloy after accumulative roll-bonding and annealing

Development and Evolution of Biaxial Texture of Rolled Nickel Tapes by Ion Beam Bombardment for High Tc Coated Conductors