Abstract:Composite materials offer numerous advantages in a wide range of applications, including thermoelectrics. Here, semiconductor-metal composites are produced by just blending nanoparticles of a sulfide semiconductor obtained in aqueous solution and at room temperature with a metallic Cu powder. The obtained blend is annealed in a reducing atmosphere and afterward consolidated into dense polycrystalline pellets through spark plasma sintering (SPS). We observe that, during the annealing process, the presence of metallic copper activates a partial reduction of the PbS, resulting in the formation of PbS-Pb-CuxS composites. The presence of metallic lead during the SPS process habilitates the liquid-phase sintering of the composite. Besides, by comparing the transport properties of PbS, the PbS-Pb-CuxS composites, and PbS-CuxS composites obtained by blending PbS and CuxS nanoparticles, we demonstrate that the presence of metallic lead decisively contributes to a strong increase of the charge carrier concentration through spillover of charge carriers enabled by the low work function of lead. The increase in charge carrier concentration translates into much higher electrical conductivities and moderately lower Seebeck coefficients. These properties translate into power factors up to 2.1 mW m-1 K-2 at ambient temperature, well above those of PbS and PbS + CuxS. Additionally, the presence of multiple phases in the final composite results in a notable decrease in the lattice thermal conductivity. Overall, the introduction of metallic copper in the initial blend results in a significant improvement of the thermoelectric performance of PbS, reaching a dimensionless thermoelectric figure of merit ZT = 1.1 at 750 K, which represents about a 400% increase over bare PbS. Besides, an average ZTave = 0.72 in the temperature range 320-773 K is demonstrated.

Comparative study on properties of n-PbS bulk thermoelectric materials prepared by chemical method

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

Facile Synthesis of Monodisperse Cu3SbSe4 Nanoparticles and Thermoelectric Performance of Cu3SbSe4 Nanoparticle-Based Materials

Nanostructures Boost the Thermoelectric Performance of PbS

Enhancing the Thermoelectric and Mechanical Properties of p-Type PbS through Band Convergence and Microstructure Regulation

Enhanced thermoelectric performance of hot-press Bi-doped n-type polycrystalline PbS

High Performance Thermoelectrics from Earth-Abundant Materials: Enhanced Figure of Merit in Pbs Through Nanostructuring Grain Size

Strategies to advance earth-abundant PbS thermoelectric

High Performance Thermoelectrics from Earth-Abundant Materials: Enhanced Figure of Merit in PbS by Second Phase Nanostructures.

Band Engineering Through Pb‐Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4

Enhanced thermoelectric properties of Pb1-xBixS prepared with hydrothermal synthesis and microwave sintering

Fabrication and Property of High-Performance Ag-Pb-Sb-Te System Semiconducting Thermoelectric Materials

PbS–Pb–Cu x S Composites for Thermoelectric Application

Effect of PbTe on Thermoelectric Properties of Co 0.88 Ni 0.12 Sb 2.91 Sn 0.09

Superior thermoelectric performance in PbTe-PbS pseudo-binary: extremely low thermal conductivity and modulated carrier concentration

Synthesis, Bottom up Assembly and Thermoelectric Properties of Sb-Doped PbS Nanocrystal Building Blocks

Insight into Carrier and Phonon Transports of PbSnS2 Crystals

Facile synthesize and enhanced thermoelectric performance of PbS with Cl doping and PbSe alloying

Contrasting Thermoelectric Transport Behaviors of p -Type PbS Caused by Doping Alkali Metals (Li and Na)

High-performance Ag0.8Pb18+xSbTe20 Thermoelectric Bulk Materials Fabricated by Mechanical Alloying and Spark Plasma Sintering