Abstract:This study presents a colloidal synthesis method to produce thermoelectric Cu3SbSe4 nanocrystals with high yield. Pb doping is employed to increase carrier concentration and effective mass, confirmed by experimental studies and theoretical calculations. Additionally, lattice distortions and other intriguing nanostructures are found to significantly reduce thermal conductivity. Consequently, the thermoelectric figure of merit zT is greatly enhanced. Developing cost‐effective and high‐performance thermoelectric (TE) materials to assemble efficient TE devices presents a multitude of challenges and opportunities. Cu3SbSe4 is a promising p‐type TE material based on relatively earth abundant elements. However, the challenge lies in its poor electrical conductivity. Herein, an efficient and scalable solution‐based approach is developed to synthesize high‐quality Cu3SbSe4 nanocrystals doped with Pb at the Sb site. After ligand displacement and annealing treatments, the dried powders are consolidated into dense pellets, and their TE properties are investigated. Pb doping effectively increases the charge carrier concentration, resulting in a significant increase in electrical conductivity, while the Seebeck coefficients remain consistently high. The calculated band structure shows that Pb doping induces band convergence, thereby increasing the effective mass. Furthermore, the large ionic radius of Pb2+ results in the generation of additional point and plane defects and interphases, dramatically enhancing phonon scattering, which significantly decreases the lattice thermal conductivity at high temperatures. Overall, a maximum figure of merit (zTmax) ≈ 0.85 at 653 K is obtained in Cu3Sb0.97Pb0.03Se4. This represents a 1.6‐fold increase compared to the undoped sample and exceeds most doped Cu3SbSe4‐based materials produced by solid‐state, demonstrating advantages of versatility and cost‐effectiveness using a solution‐based technology.

Strategies to advance earth-abundant PbS thermoelectric

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

High Performance Thermoelectrics from Earth-Abundant Materials: Enhanced Figure of Merit in Pbs Through Nanostructuring Grain Size

High Performance Thermoelectrics from Earth-Abundant Materials: Enhanced Figure of Merit in PbS by Second Phase Nanostructures.

Facile synthesize and enhanced thermoelectric performance of PbS with Cl doping and PbSe alloying

Bridging the miscibility gap towards higher thermoelectric performance of PbS

Strategies for boosting thermoelectric performance of PbSe: A review

Realizing thermoelectric cooling and power generation in N-type PbS0.6Se0.4 via lattice plainification and interstitial doping

Optimized Strategies for Advancing n-Type PbTe Thermoelectrics: A Review

Superior thermoelectric performance in PbTe-PbS pseudo-binary: extremely low thermal conductivity and modulated carrier concentration

Band Engineering Through Pb‐Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4

Synergistically optimizing carrier and phonon transport properties in n-type PbTe through I doping and SnSe alloying

Insight into Carrier and Phonon Transports of PbSnS2 Crystals

Enhancing the Thermoelectric and Mechanical Properties of p-Type PbS through Band Convergence and Microstructure Regulation

Multiscale structure and band configuration tuning to achieve high thermoelectric properties in n-type PbS bulks

Boosting the Thermoelectric Performance of PbSe from the Band Convergence Driven By Spin‐Orbit Coupling

Thermoelectric enhancement for n-type PbS via synergistic effect of Ti doping and Cu2S compositing

Enhanced thermoelectric performance of hot-press Bi-doped n-type polycrystalline PbS

Lattice Plainification Leads to High Thermoelectric Performance of P-Type PbSe Crystals

Nanostructures Boost the Thermoelectric Performance of PbS

Valence Disproportionation of GeS in the PbS Matrix Forms Pb 5 Ge 5 S 12 Inclusions with Conduction Band Alignment Leading to High n-Type Thermoelectric Performance