Abstract:Nb3Sn conductors are important candidates for high-field magnets for particle accelerators, and they continue to be widely used for many laboratory and NMR magnets. However, the critical current density, Jc, of present Nb3Sn conductors declines swiftly above 12-15T. State-of-the-art Ta- and Ti-doped strands exhibit upper critical field, Hc2, values of 24-26.5T (4.2K) and do not reach the FCC target Jc, which serves as the present stretch target for Nb3Sn development. As recently demonstrated, to meet this goal requires enhanced vortex pinning but an independent and supplementary approach is to significantly enhance Hc2. In this study, we have arc-melted multiple Nb alloys with added Hf, Zr, Ta and Ti and drawn them successfully into monofilament wires to investigate the possibilities of Hc2 enhancement through alloying. Hc2(T) was measured for all samples in fields up to 16T and some up to 31T. We have found that all alloys show good agreement with the standard Werthamer, Helfand, and Hohenberg (WHH) fitting procedure without the need to adjust the paramagnetic limitation parameter (alpha) and spin-orbit scattering parameter (lambda_so). The evaluation of dHc2/dT near Tc, which is proportional to the electronic specific heat coefficient (gamma) and the normal state resistivity (rho_n), allows a better understanding of the induced disorder introduced by alloying in the A15 phase. So far, we have observed that Hf alloying of pure Nb can enhance Hc2(0) by 3-4T to 28T, while adding just 1 at. %Hf or Zr into a Nb4Ta base alloy can raise Hc2(0) to 31T. Very importantly we find that Hf and Zr raise the alloy recrystallization temperature above the usual A15 reaction temperature range of 650°C-750°C, thus ensuring denser A15 phase nucleation in the Nb alloy grain boundaries, possibly leading to a more homogeneous A15 phase Sn content and refined A15 grain size. The potential for...

Phase formation and enhanced performance of Nb3Al prepared by spark plasma sintering and subsequent annealing

Preparation of Nb 3 Al Superconductor by Powder Metallurgy and Effect of Mechanical Alloying on the Phase Formation

Preparation of Nb3al by High-Energy Ball Milling and Superconductivity

Improved critical current density of Cu-doped Nb3Al wire through optimized Rapid-Heating Quenching and Transformation method

Strength and Superconductivity of Nb3Al Prepared by Spark Plasma Sintering

Microstructure identification of powder in tube Nb3Al wires during rapid heating process and properties of the transformed superconductors

Reproducible stable critical current density in powder-in-tube (PIT) Nb 3 Al superconductors by multi-time rapid heating and quenching process

Superconducting property improvement of RHQT Nb3Al wires through doping of Ti

Effect of Cu doping on properties of RHQT processed powder in tube Nb3Al wires

Introducing nano-scale MgO particles into RHQT Nb 3 Al superconducting wires to significantly improve the critical current density

Enhanced critical current density at high magnetic fields in MgB2 wire processed by in-situ spark plasma sintering

Phase transformation and mechanical stability of niobium aluminide (Nb3Al) induced by high pressures

Evolution from Amorphous to Nanocrystalline and Corresponding Magnetic Properties of Fe-Si-B-Cu-Nb Alloys by Melt Spinning and Spark Plasma Sintering

Microstructure, Densification and Mechanical Properties of Ti-22Al-25Nb Alloy Fabricated by Spark Plasma Sintering

Niobium based intermetallics as a source of high-current/high-magnetic field superconductors

Influence of Nb Alloying on Nb Recrystallization and the Upper Critical Field of Nb3Sn

Fabrication and thermal conductivity of AlN/BN ceramics by spark plasma sintering

Effects of High-Temperature Thermal Annealing on the Crystal Structure and Phase Separation in Sputtered ScAlN Thin Films

Microstructure and Thermal Conductivity of Spark Plasma Sintering AlN Ceramics

Microstructure and Mechanical Properties of the Powder Metallurgy Nb-16Si-24Ti-2Al-2Cr Alloy